Mitsubishi MULTI-SERIES User Manual

Press the “ SET” switch.
The off timer has been set.
“ ” is displayed in the display area. The display
then returns to the timer mode selection screen as shown below.
Step 2
<If set at 6:00 pm>
“
” (lit)
“
” (lit for 2 seconds)
‚
“
” (lit)
“
” (lit)
The air conditioning system stops operating at 6 o'clock in the afternoon.
The time display also turns off.
Press the “ SET” switch.
The remote controller goes into the OFF timer mode.
[Example] “
” flashes and
“
” turns on.
Press the or switch.
“ ” and “ ” are displayed alternately.
Set the time at which you want to stop the operation.
● Setting “hours”
Keep the or switch pressed long enough to change the “hour” display in
increments/decrements of 1 hour. Release the switch to stop changing the hours.
● Setting “minutes”
Press the
or switch briefly to increase or decrease
the displayed value by 10 minutes.
Note: If you press the “
RESET” switch, the remote
controller will return to one screen earlier and display
“
”. Step 2
5
3
4
In this mode, the air conditioning system stops the operation at the set time.
OFF TIMER MODE
Press the “ ” switch once.
This completely ends the time setting procedure.
● If you want to start operating the air conditioning system with the off timer setting, the air conditioning system must be operated before the timer is set.
● If you press the “ ” switch while in the timer setting mode, the remote controller exits from the timer mode and returns to the original display.
● If you do not press any switches for 60 seconds after entering the timer mode, the remote controller automatically exits from the
timer mode and returns to the original display.
NOTE
Press the “ SET” switch.
The on timer has been set.
The display area shows the display shown to the left.
<If set at 10:00 am>
“
” (lit)
“
” (lit)
Note: If you press the “
RESET” switch, the remote
controller will return to one screen earlier.
Press the “ SET” switch.
The remote controller goes into the ON timer mode.
[Example] “
” flashes and
“
” turns on.
Press the or switch.
“ ” and “ ” are displayed
alternately.
Set the time at which you want to start the operation.
● Setting “hours”
Keep the
or switch pressed long enough to change
the “hour” display in increments/decrements of 1 hour.
Release the switch to stop changing the hours.
● Setting “minutes”
Press the
or switch briefly to increase or decrease
the displayed value by 10 minutes.
Note: If you press the “
RESET” switch, the remote
controller will return to one screen earlier and display
“
” Step 2
5
3
4
In this mode, the air conditioning system starts the operation at the set time. The temperature at the
start of operation can also be set.
ON TIMER MODE
Press the or switch.
If you press the switch, “ ” is displayed.
If you press the
switch, “ ” is displayed.
To set the temperature at the specified time, select
“
”.
To skip temperature setting, select “
”.
● Proceed to step 7 to set the temperature.
● Proceed to step 9 if you do not wish to set the temperature.
6
6
6
2,4
3,5
1
6
2,4,6
3,5,7,9
10
8
1
Press the “ TIMER” switch.
The remote controller goes into the timer mode.
The “current day of the week” and “current time” are displayed and the
subsequent procedures are automatically displayed in the following order.
“ ” ‡ “ ” ‡ “ ”
Press the switch two times.
“ ”
‚
“
” (first press)
‚
“
” (second press)
1
2
1
Press the “ TIMER” switch.
The remote controller goes into the timer mode.
The “current day of the week” and “current time” are displayed and the
subsequent procedures are automatically displayed in the following order.
“ ” ‡ “ ” ‡ “ ”
Press the switch three times.
“ ”
‚
“
” (first press)
‚
“
” (second press)
‚
“
” (third press)
2
PCA012A001H_E_P06 05.11.16, 12:176

Mitsubishi MULTI-SERIES Specifications

General

Brand	Mitsubishi
Model	MULTI-SERIES
Category	Air Conditioner
Language	English