To Next Page

To Previous Page

NEC Display Solutions

Video Wall Installation Guide

7. IP Address assignment

There are two options, “Auto” or “Manual” for IP address assignment.

For a fast initial video wall setup, it is recommended to use the Auto-IP

functionality.

Note: When controlling the video wall via a network management system

(e.g. NEC NaViSet Administrator 2), it is recommended to assign after

setting up the video wall static IP addresses to each display, in order to

ease LAN communication to the displays

9. Auto ID / IP SETTING

Setting the monitor ID / IP address for all monitors must be performed on

the primary monitor.

Menu: MULTI-DSP > ID CONTROL > AUTO ID/IP SETTING > START > SET

Conrm number of detected monitors with “CONTINUE”

AUTO ID/IP > SETTING SETTING ITEM: ID and IP > SET

Note: The monitors’ ID and IP addresses are provided sequentially and

automatically to each connected display.

11. Auto TileMatrix Setup

Auto-conguration to distribute the input signal to the entire video wall.

Menu: MULTI-DSP > AUTO TILE MATRIX SETUP >

set number of H MONITORS & V MONITORS > ACTIVATE > SET

Note: Requires cabling setup as described in section 1.

12. Choose visual application Pre Set

For a perfect visual result, the monitors feature a factory calibrated

application Pre Set. Choose your preferred picture mode PRE-Set on the

rst screen.

Menu: PICTURE > PICTURE MODE > PRESET

Note: The SpectraView engine in each display guarantees that all displays pick

up the same factory calibrated parameters, according to the chosen PRE-Set.

13. Copy Settings (Picture settings)

To align all monitors within the video wall with the same application Pre

Set of the rst screen, copy the chosen settings to all monitors.

Menu: MULTI-DSP > SETTING COPY

Select “PICTURE” > SET

COPY START > YES

10. Chose input source for all displays

To distribute the video signal from primary monitor across all monitors,

each monitor must have DisplayPort or HDMI as input.

Congure the remote control as ID „0“ to manage all screens in parallel

(refer to section 5)

POWER ON the entire video wall (some of the displays may be in auto-

standby during conguration).

Choose the preferred INPUT source (DisplayPort or HDMI) for all displays

via the input buttons on the remote control.

Note: In the case of an OPS Slot-in PC or Media Player input, the rst

monitor must be switched to Option or Media Player. In this case, all other

monitors in the Daisy Chain remain DisplayPort or HDMI. For a detailed

Daisy Chain cable mapping table, refer to the chapter “Primary monitor -

input/output mapping” at the beginning of this guide.

8. Auto ID / IP RESET

Monitor ID / IP address reset should be performed on the rst monitor.

Menu: MULTI-DSP > ID CONTROL > AUTO ID/IP RESET > SET

Note: Auto ID Reset must be performed on the rst monitor in the LAN

daisy chain when conguration, cabling or monitors are changed or

swapped.

ID: 1 ID: 2 ID: 3

ID: 6 ID: 5 ID: 4

ID: 7 ID: 8 ID: 9

192.168.10.1

192.168.10.6

192.168.10.7

192.168.10.2

192.168.10.5

192.168.10.8

192.168.10.3

192.168.10.4

192.168.10.9

INPUT

POWER ON

Questions and Answers:

Need help?

Do you have a question about the NEC MultiSync UN552S and is the answer not in the manual?

NEC MultiSync UN552S Specifications

General

Pixel pitch	0.63 x 0.63 mm
Response time	8 ms
Display diagonal	55 \
Display brightness	700 cd/m²
Display technology	LED
Native aspect ratio	16:9
Vertical scan range	23 - 86 Hz
Horizontal scan range	26 - 134 kHz
Contrast ratio (typical)	1700:1
Display diagonal (metric)	138.78 cm
Active display area (W x H)	1209.63 x 680.34 mm
Operating hours (hours/days)	24/7
Power consumption (standby)	0.5 W
Power consumption (typical)	234 W
Maximum refresh rate	60 Hz
Annual energy consumption	341 kWh
Purpose	Universal
Orientation	Horizontal/Vertical
Product color	Black
Product design	Video wall
Placement supported	Indoor
Bezel width (bottom)	0.44 mm
Panel mounting interface	400 x 400 mm
Storage temperature (T-T)	-20 - 60 °C
Operating temperature (T-T)	0 - 40 °C
Storage relative humidity (H-H)	10 - 90 %
Operating relative humidity (H-H)	20 - 80 %
Certification	BSMI; CE; EAC; EMC B; FCC; PSB; RCM; REACH; RoHS; SASO; TÜV GS; TÜV S; UL/C-UL; VCCI
Sustainability certificates	RoHS
Cables included	AC, DisplayPort, HDMI
USB ports quantity	5
HDMI ports quantity	3
Compatible memory cards	MicroSD (TransFlash)
Ethernet LAN data rates	10, 100 Mbit/s
HDMI input ports quantity	2
Ethernet LAN (RJ-45) ports	1
Audio formats supported	AAC, MP3, WAV
Image formats supported	JPG, PNG
Video formats supported	FLV, H.264, MOV, MP4, MPG, WMV
Harmonized System (HS) code	85285210