English-28
HEAT STATUS Displays status of the FAN, BACKLIGHT and TEMPERATURE. -
FAN CONTROL Cooling fan reduces the temperature of the display to protect from overheating.
If “AUTO” is selected, you can adjust the start temperature of the cooling fan and fan speed.
AUTO, HIGH
SCREEN SAVER Use the SCREEN SAVER function to reduce the risk of Image Persistence.
NOTE: This function is released when INPUT CONFIGURATION is active. When SCREEN
SAVER is ON, the image will be changed FULL image. After released SCREEN SAVER, the
image will be displayed with current ASPECT setting.
3840 x 2160 (60 Hz) input cannot be selected.
When SCREEN SAVER is active, MULTI PICTURE, STILL, IMAGE FLIP except for NONE or
TEXT TICKER, POINT ZOOM are not available.
GAMMA*
The display gamma is changed and fi xed when “ON” is selected. OFF
BACKLIGHT* The brightness of backlight is decreased when “ON” is selected.
NOTE: Do not select this function when ROOM LIGHT SENSING is MODE1 or MODE2.
OFF
MOTION The screen image is slightly expanded and moves in 4 directions (UP, DOWN, RIGHT, LEFT) at
user determined intervals. You can set interval time and zooming ratio.
OFF
SIDE BORDER COLOR Adjusts the color of the side borders when a 4:3 image is displayed.
Press + button, the bar will become lighter.
Press - button, the bar will become darker.
15
CHANGE PASSWORD Allows the security password to be changed.
The factory preset password is 0000.
-
SECURITY Locks the security password. OFF
RESET Resets the following settings within the DISPLAY PROTECTION menu back to factory setting:
POWER SAVE, FAN CONTROL, SCREEN SAVER, SIDE BORDER COLOR.
-
EXTERNAL CONTROL
NETWORK
INFORMATION
Displays current network settings. -
IP ADDRESS SETTINGS NOTE: When changing the LAN SETTING, you need to wait several seconds until the LAN
SETTING is applied.
IP SETTING Enabling this option automatically assigns an IP address to the monitor from your DHCP server.
Disabling this option allows you to register the IP address or subnet mask number obtained from
your network administrator.
NOTE: Consult your network administrator for the IP address when “AUTO” is selected for
[IP SETTING].
AUTO
IP ADDRESS Set your IP address of the network connected to the monitor when “MANUAL” is selected for
[IP SETTING].
192.168.0.10
SUBNET MASK Set your subnet mask number of the network connected to the monitor when “MANUAL” is
selected for [IP SETTING].
255.255.255.0
DEFAULT GATEWAY Set your default gateway of the network connected to the monitor when “MANUAL” is selected
for [IP SETTING].
NOTE: Set as [0.0.0.0] to delete the setting.
0.0.0.0
DNS Set for IP ADDRESS SETTINGS of DNS server.
AUTO: Automatically assign an IP address of DNS server connected to the monitor.
MANUAL: Set your IP address of DNS server connected to the monitor.
AUTO
DNS PRIMARY Set your primary DNS settings of the network connected to the monitor.
NOTE: Set as [0.0.0.0] to delete the setting.
0.0.0.0
DNS SECONDARY Set your secondary DNS settings of the network connected to the monitor.
NOTE: Set as [0.0.0.0] to delete the setting.
0.0.0.0
LAN POWER Selects LAN operation mode. When “ON” selected, allows to supply power to LAN during power
save mode or standby mode.
NOTE: For enabling “AUTO ID”, this function should be ON.
OFF
DDC/CI ENABLE/DISABLE: Turns ON or OFF the two way communication and control of the monitor. ENABLE
PING Confi rm the response by communicating to the preset IP address. 192.168.0.10
NO
IP ADDRESS RESET Resets IP ADDRESS SETTINGS back to factory settings. -
RESET Resets the following setting within the EXTERNAL CONTROL menu back to factory settings:
DDC/CI.
-
*: If SPECTRAVIEW ENGINE is ON, this function is grayed out.
To Next Page
Loading...
Need help?
General