EasyManuals Logo
Home>NetComm>Adapter>POWERLINE SERIES

NetComm POWERLINE SERIES User Manual

NetComm POWERLINE SERIES
26 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #5 background imageLoading...
Page #5 background image
YML285 Powerline Adapters User Guide285 Powerline Adapters User Guide Powerline Adapters User GuidePowerline Adapters User Guide
www.netcomm.com.au 5
NetComm Powerline
TM
Series - Powerline Adapters 85Mbps Twin Pack
Important Safety Instructions
Please read these instructions carefully:
1. Unplug the NP285 Powerline Adapter from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp
cloth for cleaning.
2. Do not use the NP285 Powerline Adapter near water.
3. The NP285 Powerline Adapter should never be placed near or over a radiator or heat source, or in a built-in installation unless proper
ventilation is provided.
4. The NP285 Powerline Adapter should be only connected to a 240Volt power circuit. If you are not sure of the type of power available,
consult your dealer or local power company.
5. The NP285 Powerline Adapter relies on the buildings electrical installation for short-circuit (over current) protection. Ensure that a fuse or
circuit breaker no larger than 240 VAC is used on the phase conductors (all current-carrying conductors).
6. For maximum performance we advise that you do not use an extension cord or multi power board between the adapter and the AC
power source. Plug the NP285 Powerline Adapter directly into a 240V AC power point if possible.
7. Do not attempt to service the NP285 Powerline Adapter yourself, as opening or removing covers will expose you to dangerous electrical
voltage points and will also void your product warranty.
8. Refer the product to a qualied service personnel for the following conditions:
If liquid has been spilled into the product.
If the product has been exposed to rain or water.
If the product does not operate normally when the operating instructions are followed.
If the product exhibits a distinct change in performance.
System Requirements
NP285 Powerline Adapter is compatible with all TCP/IP operating systems with Ethernet port. Drivers are not required for this adapter, but you can
use the supplied Conguration Utility software to assign the network passwords.
Your computer must meet the following requirements in order to use the NP285 Powerline Adapter Conguration Utility:
Windows Operating Systems:
Windows 98SE, Windows Me, Windows 2000, Windows XP, Windows Vista or Windows 7 with Ethernet connection (for manual
conguration). As above and MAC operating systems if using automatic plug and play conguration
Pentium III 300 MHz MMX PC or greater
At least 128MB hard disk space and memory
CD-ROM drive
Note: Your computer or the device to which you want to connect the NP285 Powerline Adapter must have an Ethernet port, i.e. a network card or a network Adapter.
Getting to Know Your NP285
The NP285 Powerline Adapter has three lights indicator (LEDs) and an RJ-45 Ethernet port:
PWR: Lights up when connected to AC power supply.
PL-LINK: Lights up when detected and connected with another HomePlug Adapter within the network.
ETH-LINK/ACT: Lights up when connected to the Ethernet port of the computer or other Ethernet devices.
Flashes during data transfer.
ETHERNET: This is the connection point for connecting it to a computer or other devices with Ethernet port.

Other manuals for NetComm POWERLINE SERIES

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the NetComm POWERLINE SERIES and is the answer not in the manual?

NetComm POWERLINE SERIES Specifications

General IconGeneral
BrandNetComm
ModelPOWERLINE SERIES
CategoryAdapter
LanguageEnglish

Related product manuals