EasyManuals Logo
Home>NETGEAR>Switch>GS110EMX

NETGEAR GS110EMX Installation Guide

NETGEAR GS110EMX
2 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
Installation Guide
1. Register With the NETGEAR Insight App
Use the NETGEAR Insight app to register your switch, activate your warranty, and
access support.
1. On your iOS or Android mobile device or tablet, visit the app store, search
for NETGEAR Insight, and download the latest version of the app.
2. Open the NETGEAR Insight app.
3. If you did not set up a NETGEAR account, tap Create NETGEAR Account and
follow the onscreen instructions.
4. Enter the email address and password for your account and tap LOG IN.
If your mobile device is connected with WiFi to the same network as the
switch, the switch displays in the list of Insight Manageable Devices.
5. Either tap the switch in the list, or tap + in the upper right corner.
If you tapped +, enter the serial number on the bottom of the switch, or scan
the serial number bar code with the camera on your mobile device or tablet.
Then tap Go.
6. Follow the onscreen instructions to add your switch to a network location.
The switch is registered and added to your account.
2. Connect the Switch
1. Connect devices to the RJ-45 network ports on the switch front panel.
Ports 1 through 8 support 1G, 100M, and 10M. Ports 9 and 10 support 10G,
5G, 2.5G, 1G, and 100M.
2. Connect one RJ-45 port on the switch to a network. In a high-speed network,
use port 9 or 10.
Cables and Speeds
The following table describes the network cables that you can use for the switch
connections and the speeds that these cables can support, up to 100 meters
(328 feet).
Speed Cable Type
100 Mbps Category 5 (Cat 5) or higher rated
1 Gbps, 2.5 Gbps, or 5 Gbps Category 5e (Cat 5e) or higher rated
10 Gbps Category 6A (Cat 6A) or higher rated
Note: For speeds of 10 Gbps, if the cable length is shorter than 55 meters
(180 feet), you can use a Category 6 (Cat 6) cable.
3. Discover the IP Address
An IP address is required to congure your switch. The switch gets an IP
address from a DHCP server (such as your router) by default. If your switch is not
connected to a DHCP server, use the default IP address: 192.168.0.239.
1. Connect your mobile device to the same WiFi network as the switch.
2. Make sure that the network connects to the Internet.
3. Launch the NETGEAR Insight app from your mobile device.
4. Log in to your account.
The current IP address of the switch displays.
8-Port Gigabit Ethernet Smart Managed Plus
Switch with 2-Port 10G/Multi-Gig Uplinks
GS110EMX
Package Contents
Switch model GS110EMX
Power adapter (varies by region)
Rack-mount kit
Wall-mount screws for wall installation
Rubber feet for desktop installation
Installation guide
Ethernet cables not included.
Internet
Switch
Router
IP camera
Desktop
ReadyNAS
Smart TV
Laptop
Sample Connections
Desktop
Gaming console
Continued on the other side.

Other manuals for NETGEAR GS110EMX

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the NETGEAR GS110EMX and is the answer not in the manual?

NETGEAR GS110EMX Specifications

General IconGeneral
Switch typeManaged
Switch layerL2/L3
Quality of Service (QoS) supportYes
Number of VLANs64
Networking standardsIEEE 802.1Q, IEEE 802.1p, IEEE 802.3az, IEEE 802.3x
Virtual LAN featuresVoice VLAN, Tagged VLAN, Port-based VLAN
Cable types supportedCat5, Cat5e, Cat6, Cat6a, Cat7
DHCP featuresDHCP client
Queue scheduling algorithmsWeighted Round Robin (WRR)
Noise level0 dB
Power connectorDC-in jack
Installed SFP modules quantity0
Gigabit Ethernet (copper) ports quantity8
Basic switching RJ-45 Ethernet ports typeGigabit Ethernet (10/100/1000)
Basic switching RJ-45 Ethernet ports quantity10
Jumbo frames10240
Forwarding rate41.664 Mpps
Latency (1 Gbps)4 µs
Latency (10 Gbps)3 µs
MAC address table16000 entries
Packet buffer memory0.128 MB
Latency (10-100 Mbps)7 µs
Number of multicast groups filtered128
SafetyUL/cUL Listed (UL 60950-1)/CAN/CSA C22.2 No. 60960-1-07, EN 60950-1: 2006 + A11:2009 + A1:2010 + A12:2011 + A2:2013, IEC 60950-1:2005 (ed.2)+A1:2009+A2:2013, AS/NZS 60950.1:2015
Stackable-
Certification47 CFR FCC Part 15, SubpartB, Class B ICES-003:2016 Issue 6, Class B ANSI C63.4:2014 N 55032:2012 +AC:2013 / CISPR 32:2012 / AS/NZS CISPR 32:2013, Class B EN 55032:2015 +AC:2016 / CISPR 32:2015 +COR1:2016 / AS/NZS CISPR 32:2015, Class B EN 61000-3-2:2014 EN 61000-3-3:2013 EN 55024:2010 +A1:2015
Product colorBlack
LED indicatorsLink, Power, Speed
Number of fans0 fan(s)
Housing materialMetal
Electromagnetic compatibilityClass B
Output current2.5 A
Output voltage12 V
Power consumption (max)15.6 W
Power consumption (typical)6.6 W
Heat dissipation53.35 BTU/h
Operating altitude0 - 3000 m
Storage temperature (T-T)-20 - 70 °C
Operating temperature (T-T)0 - 40 °C
Storage relative humidity (H-H)0 - 95 %
Operating relative humidity (H-H)0 - 90 %
Package depth270 mm
Package width164 mm
Package height85 mm
Package weight1340 g
Shipping (inner) case width490 mm
Shipping (inner) case height339 mm
Shipping (inner) case length391 mm
Shipping (inner) case net weight15460 g
Number of layers per pallet (air)4 pc(s)
Number of cartons per pallet layer6 pc(s)
Quantity per shipping (inner) case10 pc(s)
Harmonized System (HS) code85176990
Weight and Dimensions IconWeight and Dimensions
Depth102 mm
Width236 mm
Height27 mm
Weight750 g

Related product manuals