English – 11
6
OPTIONAL ACCESSORIES
The following optional accessories are available:
ACCESSORIES for the 230V / 120V version ACCESSORIES for the 24V (230V / 120V) version
PLA10 PLA10
PLA11 PLA11
PS124
Refer to the user manuals of the various individual products.
7
MAINTENANCE
To ensure that the level of safety of the installation is maintained and that the system remains reliable and operational, it must be serviced regularly
in observance of the safety regulations given in this manual and established legislation.
The gearmotor must be serviced no later than 6 months after commissioning.
01. Disconnect all power supplies
02. Check for any deterioration in automation system components, paying special attention to erosion or oxidation of its structural parts.
Replace any parts which are below the required standard.
03. Check that all screw fasteners are fully tightened down
04. Check the wear of all moving parts and replace any worn components
05. Connect the power supplies up again, and run all the tests and checks described in Chapter 4
For the other equipment in the system, refer to its user manuals.
CE Declaration of Conformity and declaration of incorporation of partly completed machinery
Declaration in accordance with the following Directives: 12004/108/EC (EMC); 2006/42/EC (MD) annex II, part B
Note – The content of this declaration corresponds to that specified in the official document deposited at the Nice S.p.A. headquarters
and, in particular, to the latest revised edition available prior to the publishing of this manual. The text herein has been re-edited for edi-
torial purposes. A copy of the original declaration can be requested from Nice S.p.A. (prov. of Treviso) Italy.
Declaration number: 507/TOO Revision: 3 Language: EN
Manufacturer's Name: NICE s.p.a.
Address: Via Pezza Alta N°13, 31046 Rustignè di Oderzo (TV) Italy
Person authorized to compile the technical documentation: NICE s.p.a.
Type of product: Telescopic motor for swing gates
Model / Type: TOO3000, TOO3024, TOO4500, TOO4524, TOO3000/V1, TOO4500/V1
Accessories:
The undersigned Mauro Sordini, as Chief Executive Officer, hereby declares under his own responsibility that the products identified above
comply with the provisions of the following directives:
• DIRECTIVE 2004/108/EC OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 15 December 2004 on the approximation of
the laws of the Member States relating to electromagnetic compatibility and repealing Directive 89/336/EEC, in accordance with fol-
lowing harmonised standards: EN 61000-6-2:2005, EN 61000-6-4:2007 + A1:2011
In addition, the product conforms to the following directive in accordance with the provisions applicable to partly completed machinery:
• Directive 2006/42/EC of the European Parliament and of the Council of 17 May 2006 on machinery, and amending Directive 95/16/EC
(recast), in accordance with the following harmonised standards:
• I hereby declare that the pertinent technical documentation has been drafted in accordance with Annex VII B of Directive 2006/42/EC
and that the following essential requirements have been satisfied: 1.1.1- 1.1.2- 1.1.3- 1.2.1-1.2.6- 1.5.1-1.5.2- 1.5.5- 1.5.6- 1.5.7-
1.5.8- 1.5.10- 1.5.11
• The manufacturer agrees to submit pertinent information on the partly completed machinery to the national authorities, in response to a
motivated request, without affecting its intellectual property rights.
• If the partly completed machinery is operated in a European country with an official language other than the language used in this dec-
laration, the importer must include a translation with this declaration.
• The partly completed machinery must not be operated until the final machine in which it is to be incorporated is declared to conform to
the provisions of Directive 2006/42/EC, if applicable.
The product also complies with the following standards: EN 60335-1:2002 + A1:2004 + A11:2004 + A12:2006 + A2:2006 + A13:2008 +
A14:2010 + A15:2011; EN 60335-2-103:2003 +A11:2009
The parts of the product which are subject to the following standards comply with them:
EN 13241-1:2003+A1:2011, EN 12445:2002, EN 12453:2002, EN 12978:2003+A1:2009
Oderzo, 19 November 2015 Mr. Mauro Sordini
(Chief Executive Officer)
To Next Page
Loading...
Need help?
General
