Pandora DXL 0110L User Manual

2322
USER MANUAL
PANDORA DXL 0110L CAR SERVICE-SECURITY SYSTEM
Changing «Service PIN-code»:
• Enter the first digit of the code using VALET button. Press the button a
number of times, equal to the first digit. Pauses between presses should not
exceed 1 second, every pressing will confirm with orange LED indicator flash.
Pause for more than 1 second and red LED indicator with a short sound signal
of the Beeper confirm the input of the first digit. Then you can enter the next
digit.
• Enter the other numbers in the same manner. The input of the fourth
number will be confirmed by series of red and green LED indicator flashes
with multiple sound signals of the Beeper. The system will wait for PIN-code
re-entering.
• Enter all four digits again;
• If you were able to correctly enter code twice, the indicator will
produce series of red and green flashes and the Beeper will emit the series
of sound signals, new PIN-code will be recorded, the system will return to the
programming mode. In case of the incorrect code input the indicator will be
lit red and the Beeper will emit a long sound signal,the system will return to a
programming mode.
Level 3 – Recording idle speed
To timely turn off the starter during automatic or remote engine start
via digital or analog tachometer output and the correct operation of the
«Smart Turbo Timer», it is necessary to record the engine’s idle speed.
To record idle speed to the non-volatile system’s memory, enter the
programming menu. Press VALET button three times. Switch on the ignition
and start the engine after entering this level of programming (the engine
should be warmed-up, idle speed should match the stable idle speed of the
warmed-up engine). The system will confirm the presence of the idle speed
status with green flashes of the LED status indicator. Wait until the stable idle
speed will be reached and save the changes.
Saving changes:
Press VALET button once to save idle speed. Successful recording of the idle
speed will be confirmed with the series of red and green flashes of the LED
status indicator and the series of sound signals of the Beeper. The system will
exit programming menu and reboot after saving idle speed.
Level 4 – Resetting to factory settings.
The procedure recovers the system’s factory settings without deleting
previously registered devices (tags, mobile device, relays, etc.), that was
previously stored in the non-volatile memory.
To reset the factory settings enter the programming mode and press VALET
button four times. Press and hold VALET button for more than 4 seconds until
siren/Beeper sound, then release the button. The system will confirm the
resetting to the factory settings with a long red flash of the LED indicator with
the multiple sound signals of the Beeper. After that the system will return to a
programming mode.
Level 5 – Registration of Bluetooth engine compartment module
To register the Bluetooth engine compartment module, enter the programming
mode and press VALET button 5 times. The LED indicator will light green and
the system will enter the registration of the engine compartment module
mode. Connect the module in accordance with installation manual. The system
will confirm the registration with a short sound signal of the Beeper.
Save changes:
To finish the registration of the engine compartment module, VALET button
should be pressed once again, the series of red and green flashes of the status
LED indicator with the multiple sound signals of the Beeper will confirm the
saving, switch on the ignition to automatically save the settings and exit the
programming mode.
Level 6, 7 – Registration of Bluetooth radio relays №1, №2
The registration of radio relays is performed one by one starting from
the 6 level: radio relay №1 is registered at the 6 level; radio relay №2 is
registered at the 7 level. The radio relay can be overwritten only at the
level of its initial registration.
To register of the Bluetooth radio relays 1, 2, enter the programming
mode and press VALET button 6 times for radio relay 1 or 7 times for radio
relay 2. The LED indicator will light green and the system will enter the
registration of the radio relay mode. Connect the relay in accordance with
installation manual. The system will confirm the registration with a short sound
signal of the siren/Beeper.
Save changes:
To finish the registration of the Bluetooth radio relay, VALET button should

Pandora DXL 0110L Specifications

General

Brand	Pandora
Model	DXL 0110L
Category	Car Alarm
Language	English