Philips 711 User Manual

15
Connecting to optional equipment
Connecting to an amplifier equipped with two channel
analog stereo
● Connect the audio Left and Right out jacks of the DVD player to the
audio left and right in jack on your amplifier, receiver or stereo system,
using an audio cable (E).
Connecting to an amplifier equipped with two channel
digital stereo (PCM)
1 Connect the player’s digital audio out jack (optical G or coaxial F) to the
corresponding in jack on your amplifier.
Use an optional digital (optical G or coaxial F) audio cable.
2 You will need to activate the player’s digital output (see ‘Personal
Preferences’).
Connecting to an A/V receiver equipped with a multi-
channel decoder (Dolby Digital™(AC-3), MPEG 2 and
DTS)
Digital Multi-channel sound
Digital multi-channel connection provides the best sound quality. For this you
need a multi-channel A/V receiver that supports one or more of the audio
formats supported by your DVD player (MPEG 2, Dolby Digital™(AC-3),
AC3 and DTS). Check the receiver manual and the logos on the front of the
receiver.
1 Connect the DVD player’s digital audio output (optical G or coaxial F) to
the corresponding input on the receiver using an optional digital (optical
G or coaxial F) audio cable.
2 You will need to activate the player’s digital output (see ‘Personal
Preferences’).
Note:
If the audio format of the digital output does not match the capabilities of your
receiver, the receiver will produce a strong, distorted sound or no sound at all. The
selected audio format of the DVD is displayed in the Status Window when the
Menu OSD is activated or Audio button is activated.
Six Channel Digital Surround Sound via digital connection can only be obtained if
your receiver is equipped with a Digital Multi-channel decoder.
To see the selected audio format of the current DVD in the Status Window, press
the MENU OSD or the Audio Language selector button.
PREPARATION
TV
AMPLIFIER
L
R
(CVBS)
VIDEO OUT
DIG OUT
AUDIO OUT
S-VIDEO OUT
OPT OUT
DIGITAL AUDIO OUT
PCM/MPEG2/AC3/DTS
STEREO OUT
(Y/C)
I
AUX/VCR
IN
II
TV OUT
MAINS
GFE
All

Philips 711 Specifications

Optical Readout System

laser type	Semiconductor AlGaAs
numerical aperture (DVD)	0.60
numerical aperture (VCD/CD)	0.45
wavelength (DVD)	650 nm
wavelength (VCD/CD)	780 nm

DVD Disc Format

medium	Optical Disc
diameter	12 cm (8 cm)
playing time (one layer, 12 cm)	2.15 h
playing time (dual layer, 12 cm)	4 h
playing time (two side, single layer)	4.30 h
playing time (two side, dual layer)	8 h

TV Standard

europe	PAL/50Hz
usa	NTSC/60Hz
number of lines (PAL)	625
number of lines (NTSC)	525
playback	Multistandard (PAL/NTSC)

Video Format

DA converter	10 bits
signal handling	Components
digital compression (DVD)	MPEG2
digital compression (VCD)	MPEG1
horizontal resolution (DVD)	720 pixels
vertical resolution (DVD)	576 lines
horizontal resolution (VCD)	352 pixels
vertical resolution (VCD)	288 lines

Video Performance

video output	1 Vpp into 75 ohm
S-Video output (Y)	1 Vpp into 75 ohm
S-Video output (C)	0.3 Vpp into 75 ohm
RGB output	1 Vpp into 75 ohm

Audio Format

digital audio	MPEG Compressed Digital
DTS/AC-3	Supported
PCM	16, 20, 24 bits
sampling frequencies	44.1, 48, 96 kHz
analog sound	Stereo
Dolby Pro Logic downmix	Supported
3D sound	Virtual 5.1 channel on 2 speakers

Audio Performance

DA converter	24 bits
DVD sampling frequency	96 kHz 4 Hz - 44 kHz
sampling frequency (48 kHz)	4 Hz - 22 kHz
CD sampling frequency	44.1 kHz 4 Hz - 20 kHz
signal-to-noise ratio (1kHz)	103 dB
dynamic range (1kHz)	98 dB
crosstalk (1kHz)	115 dB
distortion and noise (1kHz)	95 dB

Connections

SCART	2x
S-Video output	Mini DIN, 4 pins
video output	Cinch (yellow)
audio L+R output	Cinch (white/red)
digital output	1 coaxial, 1 optical
IEC958	for CDDA / LPCM
IEC1937	for MPEG1/2, AC-3 and DTS

Cabinet

dimensions (w x h x d)	435 x 92 x 320 mm
weight	Approx. 4 Kg