Pioneer CT-W851R User Manual

RECORDING
RELAY RECORDING (from DECK I to DECK II)
| (CT-W851R/CT-W801R/CT-W701R only)
1, Load tapes for recording in DECK | and DECK Il.
2. Press the RELAY/SKIP button, turning the RELAY/SKIP
indicator on.
3. If you use AUTO BLE tuning, see page 15.
4. If you use SOUND EQ function, set the SOUND EO
switch (see page 8}.
5, Set the DOLBY NR switches of both DECK | and DECK II.
6. Set the REV MODE switch.
® To record on one side only, set the switch to the == posi-
tion. To record on both sides, set the switch to either the
=>' or the ¢ position.
Press the recording (@) button of DECK 1.
Prepare the audio source from which you wish to record.
Turn on the stereo amplifier and prepare it for playback
of the desired audio source.
9. Adjust the recording level. For details, see page 14 *“AD-
JUSTING THE RECORDING LEVEL”’.
10. Press the playback (> or <) button of DECK | to begin
recording.
@ When recording on both sides, press the ® button, If the
4 button is pressed, recording will stop after only one side
is recorded.
@ When the tape in deck one ends, the other deck automati-
cally begins recording.
® To cancel relay recording, press the RELAY/SKIP button once
again (turning the RELAY/SKIP indicator off}.
ox
NOTES:
* When erasure prevention tabs are broken, you Cannot record
even if you press the recording { @) button.
* Always set TIMER MODE switch to OFF.
* You cannot relay-record from DECK tl to DECK I.
To stop recording temporarily
Press the pause (IM) button of operating deck.
©
To
resume
recording,
either
press
the
pause
(E19)
button
again,
or press the playback ( or <4} button.
To stop recording
Press the stop (™@) button of operating deck.
16
<RRB1I120>
En
RELAY RECORDING SEQUENCE WITH REVERSE
MODE SWITCH SETTING
The recording sequence depends on the setting of the REV MODE
switch and on which playback (P or <) button is pressed first.
The playback sequence for each possible selection is shown below.
© Relay recording is always begun from the direction indicated by
the tape transport indicator (PD or <j). To change this direction,
press the desired playback (P or <) button, then immediately
press the stop (MH) button.
& : DECK | forward recording
J: DECK | reverse recording
D : DECK if forward recording
<i: DECK Il reverse recording
co: Auto-reverse function
—~ =: Relay
REV Starting | Another
MODE | playback deck
switch | button | mode
Recording sequence
=z [peck im] oe | ib n>
== [DECK Im] oi | iD oH
Sz DECK 14) > Id >
= beck i ie Tia-na
Dor > |DECK IP “HW | [Deol <dl> coll 4
Dorea|DECKIP| ll | 1>awld—ia
=> or ew i/DECK 14 11> {I-+UPootia
Dor ew |DECK 14] it
{d-lid
PARALLEL RECORDING =
| (CT-W851R/CT-W801R only)
5114 4 1
cee ee
(2/9) ee
9 (2)8 6 (2) (3)
1.
Load
tapes
for
recording
in
DECK
}
and
DECK
Hl.
2.
If you
use
AUTO
BLE
tuning,
see
page
15.
3.
Hf
you
use
SOUND
EQ
function,
set
the
SOUND
EQ
switch
(see
page
8).
4.
Set
the
type
of
the
DOLBY
NR
switch
on
DECK
1.
©
You
cannot
set
different
types
of
the
DOLBY
NR
system
for
DECK
|
and
DECK
Hi. (The
type
of
the
DOLBY
NR
system
for
DECK
|is
applied
to
DECK
II.
Therefore,
the
setting
for
DECK
ll
is
ignored
and
the
indicator
for
it
is
the
same
as
the
one
set
for
DECK
1.3
5.
Set
the
REV
MODE
switch.
®@
To
record
on
one
side
only,
set
the
switch
te
the
==
posi-
tion.
To
record
on
both
sides,
set
the
switch
to
either
the
=>
of
the
ed
position.
6.
Press
the
recording
(@)
button
of
DECK
I.
7.
Prepare
the
audio
source
from
which
you
wish
to
record.
Turn
on
the
stereo
amplifier
and
prepare
it
for
playback
of
the
desired
audio
source.

Pioneer CT-W851R Specifications

General

Brand	Pioneer
Model	CT-W851R
Category	Cassette Player
Language	English