RINS987-2
Quick Reference Guide
If a device connected to the PCX is not installed correctly or
lost communication with the panel, “DEVICE FAIL” will be
shown on the LCD keypad followed by a 3-figure device code.
The first digit identifies each type of device:
The digits after refer to that devices address, for example:
DEVICE FAIL 401 = Means that the Remote Input Expander
addressed as 01 has a problem. Check the connections
DEVICE FAIL 202 = Means that the LCD keypad addressed
as 02 has a problem. Check the connections.
DIGI COM FAIL 100: Call to ARC failed. Check all ARC call
details and signalling formats.
MODEM FAULT: System unable to communicate with digi
modem card. Check that it is installed properly (power
system down before removing it/installing it).
Entering The Engineers Menu
Exiting The Engineers Menu
Engineers mode can only be entered if all partitions
are disarmed.
Enter your Engineers code (default 9999)
Any faults will be shown.
Press m
‘ARM/DISARM THE SYSTEM’ will be displayed.
Press m
‘FORCE ARM ON 1st INPUT[01]’ will be displayed
(can be used to quick arm the system. Press m
The keypad will start
beeping, and ‘Enter Code’
will be displayed.
Enter your engineers code again.
‘INHIBIT FIRE/HU’ will be shown
!!
D
C
B
A
ENTER CODE
[ ]
!!
D
C
B
A
Active Faults
BatteryFault100
In Engineers Mode, press m, until you reach a main menu
item (i.e. in capital letters).
Press ¤
!!
D
C
B
A
Please Wait
Saving NVM Data
1 = End Station
2 = Keypad
3 = Tag Reader / Door Station / RIX2
4 = Remote Input Expander
5 = Remote Output Expander
LINE FAULT: Line fault signalled by digi modem card,
check voltage across A and B terminals (50V). Check line
dials out OK with a normal telephone.
ERROR INPUT PARTITION NOT ACCESSIBLE: An input
has been programmed to a partition for which no arming
point is valid to disarm.
ENGINEER MODE ACCESS DENIED: Means that a
partition is armed on the system or a fault hasn’t been
cleared. Make sure you clear the fault or disarm the
partition on the corresponding keypad.
Fault Indictions
Fault IndictionsDevice Codes
Pyronix Limited
Pyronix House
Braithwell Way
Hellaby
Rotherham
S66 8QY
UK
Customer Support Line (UK only): 0870 122 3360
This is a national rate line
Hours of business: 7.00am - 7.30pm
E-mail: customer.support@pyronix.com
website: www.pyronix.com
Fault Analysis
Engineer Test Functions
Engineer Tests
Popular PGM Types
Diagnostics
Input Types
In the Engineers Menu, Press m until you reach
‘DIAGNOSTICS’. Press l key.
‘View PSU’s’ will be displayed.
This displays the voltages and
current for the Endstation,
RIXs, ROXs, Keypads and
Readers. Press l if you wish to view this, or press
m for the next option.
‘View Inputs’ will be displayed.
This displays the resistence values for each input on the
Endstation, RIXs, Keypads and Readers.
Press l if you wish to view this:
‘Endstation Inputs’ will be
displayed, press l key.
“cccccccc” should be
displayed if all inputs are
closed. (c = closed. o = open. F = fault (input not reading
correctly))
Press l again to view the
resistance reading of each
input.
Press m to scroll to RIX, Keypad, or Reader inputs.
‘Calibration’ will be displayed. Press m.
You will be returned to Engineers Menu.
In the Engineers Menu, Press m until you reach
‘ENGINEER TESTS’. Press l. Select a sound using the
© key to play when a test has been accepted. Press l.
‘Walk Test’ will be displayed. Press l and select the
partitions to be walk tested. Press l. The inputs will be
displayed until they have been walk tested,‘Walk Test
Complete’ will be shown once all completed. Press l.
‘Test Control’ will be displayed, this can be used to soak
test inputs for a number of days. Press l for this function
or m for thenext option.
‘Test Bell’ will be displayed. This will test both the strobe
and bell outputs. Press l for this or m for the next option.
‘Battery Load Test’ will be displayed. To perform a battery
load test press l or m for the next option.
‘Test PGM’s’ will test any PGM output on the system. This
can be used for testing signals to the central station (both
the ATE pins and Digi channels are programmed from
PGM outputs).Press l.
Enter the PGM number you would like to test (see below)
or use the { and } arrow keys to scroll through them.
Press l to test that output. Press m to cancel.Press m.
You will be returned to Engineers Menu.
!!
D
C
B
A
Input [001] [1]
04.7k CC
!!
D
C
B
A
cccoooFF
!!
D
C
B
A
Endstation PSU
13.7V 0.20A
0000
0001
0002
0003
0004
0005
0006
0007
0008
0009
0014
0016
0017
0018
Unused
Fire
Hold Up Any
Intruder Any
Final Arm All
Abort
Confirmed Any
Tamper Any
Duress
HU Device Any
Bell Any
Strobe Any
Omit Rearm Any
Unconfirmed Any
Final Arm Any
Keyswitch Disarm
Entry/Exit
Follow Input
Viper Reset
PIR Latch
Line Fault
AC Fail
Battery Fualts
Global Fault 1 (armed)
Global Fault 2 (any)
Test ATE/GSM
Test ATS
Follow inputs
0022
0025
0033
0035
0037
0039
0051
0052
0053
0055
0056
0063
0064
1000-
1256
00
01
02
03
04
05
06
07
08
09
10
Unused
Fire
Gas
HU
Silent HU
Tamper
Immediate
Entry/Exit (EE)
Access (A)
A (Part EE)
EE (Part A)
PTS
Switcher
24 Hour
Sub Part Control
Fault
Closure Supervision
Shunt Input
Disarm Input
Keyswitch Latched
Entry Shock Input
Keyswitch Pulsed
11
12
13
15
16
17
18
19
20
21
23
Resistance Values
The system diagnostics that can be displayed are: Input
resistance, system voltages and current.
The Engineer Test function allows you to walk test and soak
test inputs, toggle PGM outputs, do a battery load test and
signal communication tests.
Alarm = 4k7
Tamper = 4k7
Mask = 6k8
TS50131-3:2003
EN50131-1
PD6662
Security Grade 3
Environmental Class 2
3
To Next Page
Need help?
General
