Roborock Q7+ User Manual

10
Routine Maintenance
C
C1
Main Brush
* Clean every 2 weeks and replace every 6-12 months
C1-1—Main Brush Cover
C1-2—Latches
C1-3—Main Brush
C1-4—Main Brush Caps
C1-5—Main Brush Bearing
C1-6—Turn over the robot and press the
latches to remove the main brush cover.
C1-8—Rotate the main brush caps in the
indicated unlock direction to remove the caps.
Notes:
•
Main brush should be wiped down with wet cloth and left to
dry away from direct sunlight.
•
Do not use corrosive cleaning uid or disinfectant to clean
the main brush.
C1-7—Pull out the main brush and remove
the main brush bearing.
C2
Side Brush
1. Unscrew the side brush screw.
* Clean every month and replace every 3 to 6 months
C3
Omni-Directional Wheel
The omni-directional wheel bracket cannot be removed.Note:
C3-1—Use a tool, such as a small
screwdriver, to pry out the axle and
take out the wheel.
C3-2—Rinse the wheel and the axle with
water to remove any hair and dirt.
Air-dry, reinstall, and press the wheel
and axle back in place.
* Clean as needed
C5-2—Remove the washable lter and
empty the dustbin.
C5-1—Open the upper cover of the robot
and take out the dustbin.
C5
Dustbin and Washable Filter
* Clean every week and lter should be replaced every 6-12 months.
Note: To prevent blockage, only use clean water without any
cleaning liquid.
Note: Do not touch the surface of the lter with your hands,
brush, or hard objects to avoid potential damage.
C5-3—Fill the dustbin with clean water.
Gently shake the dustbin, and then
pour out the dirty water.
C5-4—Rinse the washable filter repeatedly and tap
it to remove as much dirt as possible.
C5-5—Leave the dustbin and the washable
lter to dry and reinstall them.
Notes:
•
After cleaning, always remove the mop cloth to prevent dirty
water from leaching back into the clean water tank.
•
A dirty mop cloth will compromise the washing
performance. Clean it before use.
C6
Mop Cloth
C6-1—Remove the mop cloth from the
mopping module. Wash and air dry
the mop cloth.
* Clean after each use and replace every 3 to 6 months
C7-1—Mop Attachment Slot
* Replace them every 1 to 3 months
C7
Filter Components
Note: To ensure cleaning performance, replace the lter
components every 1 to 3 months, depending on the water
quality and how often you use the robot.
1. Move your nger along the notch to
remove each lter.
2. Insert new lter components and make
sure they are properly installed.
C8
Dust Bag Replacement
*
Replace as needed.
Note: The dust bag handle seals the bag on removal to prevent
dust leakage.
C8-1—Remove the dustbin cover vertically
as shown.
C8-2—Lift the dust bag out of the dustbin
and discard it.
C8-3—Clean the lter with a dry cloth.
C1-9—After removing the tangled hair or dirt
at both ends of the main brush, reinstall
it, press on the main brush cover to
lock it in place. Make sure that the
main brush cover has been properly
attached. When properly installed,
all four tabs should be hidden.
2. Remove and clean the side brush. Reinstall
the brush and tighten the screw.
Clean the main wheels with a soft, dry cloth.
C4
Main Wheels
* Clean every month

Roborock Q7+ Specifications

General

Brand	Roborock
Model	Q7+
Category	Vacuum Cleaner
Language	English