EasyManuals Logo
Home>Scheppach>Saw>Basa 3

Scheppach Basa 3 User Manual

Scheppach Basa 3
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #24 background imageLoading...
Page #24 background image
www.scheppach.com
24
|
GB
6. Technical data
Passage width 306 mm
Passage height 205 mm
Table size 400 x 548 mm
Cutting speed 370 – 750 m/min
Saw band length 2360 mm
Height up to tabletop 490 mm
Height up to tabletop with
underframe
1025 mm
Overall height without un-
derframe
1125 mm
Overall height with under-
frame
1655 mm
Overall width 900 mm
Overall depth 540 mm
Slewing range of the table -8° – +45°
Overall weight without un-
derframe
69 kg
Overall weight with under-
frame
79 kg
Suction connector Ø 100 mm
Extraction power 565 m
3
/h
stat. under pressure (20 m/
sec)
900 Pa
Drive
Motor
Alternating
current 230-240 V ~
50 Hz
Nominal consumption P1
(kW)
0,8kW (S1)
1,1 kW (S6 40%)
Delivery of power P2 (kW)
0,56 kW (S1)
0,74kW (S6 40%)
Drive
Motor
Rotary current 400V
~ 50 Hz 3 phase
Nominal consumption P1
(kW)
0,7kW (S1)
1,1 kW (S6 40%)
Delivery of power P2 (kW)
0,48 kW (S1)
0,77kW (S6 40%)
Noise parameters
The noise emission values determined according
to EN 3746 for the sound level and according to EN
1807 (coe󰀩cient of correction k3 calculated accord-
ing to Appendix A.2 of EN 1807-1) for the sound level
at the workplace are as follows, based on the working
conditions listed in ISO 7960 Appendix J:
The values given are emission values and therefore,
are not necessarily to be seen as safe workplace
values. Although there is a link between emission
values and immission levels, it is not possible to reli-
ably determine whether additional precautions will be
required or not.
Factors inuencing the actual immission level present
at the workplace include the duration of exposure, the
nature of the workspace, other noise sources, etc., e.
g. the number of machines and adjacent operations.
The permitted workplace values may also vary from
country to country. However, this information should
enable the user to better assess hazards and risks.
Sound level in dB
Idle running L
WA
= 80.3 dB(A)
Operation L
WA
= 100.2 dB(A)
Sound level at the workplace in dB
Idle running L
pAeq
= 64.1 dB(A)
Operation L
pAeq
= 82.9 dB(A)
A measurement uncertainty allowance K = 4 dB ap-
plies to the mentioned emission values.
Dust emission details
The dust emission values measured according to the
"Principles for the testing of dust emissions (concen-
tration parameters) of woodworking machines" of the
Technical Committee for Wood are below 2 mg / m3.
This means that when the machine is connected to a
proper operational exhaust system with an air speed
of at least 20 m / s, it can be assumed that the TRK
limit value for wood dust in the Federal Republic of
Germany will always be safely below the limit.
Depending on the materials or the type of the materi-
al, note the load values of the material manufacturer.
7. Machine description
Due to its perfected design, the machine o󰀨ers a ver-
satile application for processing wood and plastics in
the workshop.
The upper and lower bandwheel is protected by a
xed guard and an articulated cover. Upon opening
the cover, the machine is switched o󰀨. Switching on
again is only possible with the cover closed. The non-
cutting part of the sawbelt above the table top is cov-
ered by a guard xed to the sawbelt guide, the latter
being protected against inadvertant opening by the
xed guard of the upper band wheel. The non-cutting
part of the sawbelt under the table top is protected by
a xed cover.
The swivelling range of the table from -20° to +47°
allows versatile cutting possibilities (e.g.)
Longitudinal cuts
Cross cuts
Diagonal cuts
Curved and irregular cuts
Cuts for dovetails and tenons
On-edge cuts of squared beams
Please consult also the working hints in the operating
instructions.

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Scheppach Basa 3 and is the answer not in the manual?

Scheppach Basa 3 Specifications

General IconGeneral
BrandScheppach
ModelBasa 3
CategorySaw
LanguageEnglish

Related product manuals