Scheppach EB1700 User Manual

12
|
GB
The fuel tank (2) must be emptied completely before
transport.
Storage
Never store an auger for longer than 30 days without
carrying out the following steps.
Follow the cleaning instructions and maintenance in-
structions before storing the device!
Storing the auger
If you store an auger for longer than 30 days, it must
be prepared ahead of time. Unless the storage in-
structions are followed, fuel remaining in the carbu-
retor will evaporate, leaving gum-like deposits. This
could lead to di󰀩cult starting and result in costly re-
pairs.
• Remove the fuel tank cap slowly to release any
pressure in tank. Carefully drain the fuel tank.
• Start the engine and let it run until the engine stops
in order to remove the fuel from the carburettor.
• Allow the engine to cool (approx. 5 minutes).
• Remove the spark plug.
• Pour 1 teaspoon of clean 2-cycle oil into the com-
bustion chamber. Pull starter rope slowly several
times to coat internal components. Replace spark
plug.
• Store the auger in a dry location, far away from po-
tential sources of ignition, such as furnaces, hot
water boilers with gas, gas dryers, etc.
Recommissioning the auger
• Remove spark plug.
• Pull starter rope briskly to clear excess oil from
combustion chamber.
• Clean the spark plug and check that the electrode
gap is correct.
• Prepare unit for operation.
• Fill fuel tank with proper fuel / oil mixture.
11. Disposal and recycling
The equipment is supplied in packaging to prevent it
from being damaged in transit. The raw materials in
this packaging can be reused or recycled. The equip-
ment and its accessories are made of various types
of material, such as metal and plastic. Defective com-
ponents must be disposed of as special waste. Ask
your dealer or your local council.
NEVER touch the hot motor.
• Remove the spark plug cover (8) by removing the
screw (G) with the provided key.
• Remove the spark plug cap (H).
• Remove the spark plug (I) and check it.
• Check the insulator. In case of damage such as
cracks or chips: Replace the spark plug (I).
• Clean the spark plug electrodes with a wire brush.
• Check the electrodes‘ gap and adjust it. Gap 0.75
mm.
• Return the spark plug (I) and tighten it with the
spark plug spanner.
• Replace the spark plug cap (H) on the spark plug
(I).
• Re-install the spark plug cover (8)
Ensure that no dirt gets into the cylinder head during
replacement.
Check the position of the spark plug (I).
• A loose spark plug (I) can damage the motor by
overheating.
• Tightening it too much can damage the thread in
the cylinder head.
The manufacturer is not liable for damage resulting
from this, the risk lies exclusively with the user.
Replacing the fuel lter g. 8
The felt lter (J) of the fuel lter can become clogged.
It is recommended to replace the fuel lter once every
three months in order to ensure unimpeded fuel ow
to the carburetor.
To remove the fuel lter for replacement, pull it out
through the tank ller neck using a piece of wire bent
at one end to form a hook.
Service information
Please note that the following parts of this product
are subject to normal or natural wear and that the fol-
lowing parts are therefore also required for use as
consumables.
Wear parts*: spark plug, drill
* Not necessarily included in the scope of delivery!
10. Storage/Transport
Transport
Leave the motor to cool down before transporting the
machine or storing it indoors in order to prevent burn-
ing and re hazards.
Turn o󰀨 the motor even for short distances when
changing locations during work.
Carry the auger exclusively by the handle. Do not
touch the casing (risk of burning).
When transporting the auger in a vehicle, it must be
stored safely.

Scheppach EB1700 Specifications

General

Brand	Scheppach
Model	EB1700
Category	Lawn and Garden Equipment
Language	English