www.scheppach.com
GB
|
25
Suction from open tanks/containers and natural
bodies of water
Use a special self-suction accessory (not included in
the scope of delivery / available from specialist deal-
er).
With this accessory, the high-pressure cleaner can
take in water 0.5 m above the water level. This can
last about 25 to 50 seconds.
Immerse the accessory’s hose completely under water
to drive the air out of the hose.
Connect the accessory’s hose to the high-pressure
cleaner, and make sure that the suction strainer re-
mains under water.
Let the high-pressure cleaner run with the spray
gun removed until the water ows evenly out of the
high-pressure hose. If no water comes out after 25
to 50 seconds, switch o and check all connections.
Once the water is owing, turn o the high-pressure
cleaner and connect the spray gun and spray lance
to start work.
High-pressure hose connection (Fig. 3/4)
Connect the high-pressure hose (2) to the connection
for the high-pressure hose (6). Remove the protective
cover rst.
Insert the other end of the high-pressure hose (2) into
the pistol connection (13).
To remove the high-pressure hose (2), press the but-
ton Taste (A) and pull it out.
Connecting the attachments (Fig. 5)
To mount attachments 14, 17, 18 and 20, press them
into the pistol (13) and turn them until the lock.
To mount the attachments 12, 15, 16, 19 and 21, in-
sert these into the extension piece (14) and turn them
until they lock.
10. Start up
m Attention!
Always make sure the product is fully assembled
before commissioning!
The machine consists of an assembly with a pump,
which is covered by a shockproof housing. The ma-
chine is equipped with a lance and a handy pistol for an
optimal working position, whose shape and equipment
comply with the applicable regulations.
9. Layout
Correct use of the device
• The high-pressure cleaner must be set up on a level,
rm surface.
• Each time the machine is operated, it is recommend-
ed to observe the correct operating position: one
hand on the gun and the other hand on the lance.
• The water jet must never be directed at electrical
lines or the machine.
• A small amount of leakage of the pump is normal
in order to avoid damaging the pump when it is at
a standstill.
• The machine must not be used in rooms where there
is a risk of explosion under any circumstances.
• The working temperature must be between +5 and
50°C. Do not cover or make changes to the lance or
spray nozzles.
• The high-pressure cleaner is designed for opera-
tion with cold or moderately warm water (max. up
to 50°C); higher temperatures will cause damage to
the pump.
• The incoming water must not be dirty, sandy or con-
taminated with chemical products that can impair the
function and decrease the durability of the machine.
Assembly
Assembling the device (Fig. 1)
Push the handle (1) onto the fastening points at the top
of the device and secure using the two screws provid-
ed (length 20 mm).
Water supply connection (Fig. 2)
Screw the connection for the water supply (10) on-
to the device. The connection for the water supply
(11) features a connection for standard hose coupling
systems. Attach the hose coupling of the supply hose
(min. Ø 1/2”/ approx. 13 mm) onto the connection for
the water supply (10).
Always use an enhanced water hose with an indus-
try-standard coupling for the water supply. The length
should be at least 6.0 m. (Not included in the scope
of delivery)
A backow prevention device must be installed be-
tween the drinking water and the high-pressure clean-
er! Ask your plumbing expert about this.
To Next Page
Loading...
Need help?
General
