Scheppach HM254 User Manual

www.scheppach.com
GB
|
33
• Do not load the machine unnecessarily: excessive
pressure when sawing will quickly damage the saw
blade, which results in reduced output of the machi-
ne in the processing and in cut precision.
• When cutting plastic material, please always use
clamps: the parts which should be cut must always
be xed between the clamps.
• Avoid accidental starting of the machine: the opera-
ting button may not be pressed when inserting the
plug in an outlet.
• Use the tool that is recommended in this manual.
In doing so, your machine provides optimal perfor-
mance.
• Hands may never enter the processing zone when
the machine is in operation.
• Release the handle button and switch o󰀨 the machi-
ne prior to any operations.
m WARNING! This electric tool generates an electro-
magnetic eld during operation. This eld can impair
active or passive medical implants under certain con-
ditions. In order to prevent the risk of serious or deadly
injuries, we recommend that persons with medical im-
plants consult with their physician and the manufactu-
rer of the medical implant prior to operating the electric
tool.
6. Technical data
AC motor 220 - 240 V 50Hz
Power S1 2000 Watt
Idle speed n
0
4500 min
-1
Carbide saw blade ø 255 x ø 30 x 2.8 mm
Number of teeth 48
Maximum tooth width of
saw blade
3 mm
Swivel range -45° / 0°/ +45°
Mitre cut 0° to 45° to the left
Saw width at 90° 340 x 90 mm
Saw width at 45° 240 x 90 mm
Saw width at 2 x 45°
(double mitre cut)
240 x 45 mm
Protection class II
Weight ca. 14.3 kg
Laser class 2
Wavelength of laser 650 nm
Laser output < 1 mW
Technical changes reserved!
22. Workpiece support extensions must always be
secured and used during work.
23. Replace table inserts when worn!
24. Avoid overheating of the saw teeth.
25. When sawing plastic, avoid melting of the plastic.
Use the appropriate saw blades for this purpose.
Replace damaged or worn saw blades immedia-
tely.
When the saw blade overheats, stop the machine.
Allow the saw blade to cool down before using the
machine again.
Attention: Laser radiation
Do not stare into the beam
Class 2 laser
Protect yourself and you environment from ac-
cidents using suitable precautionary measures!
• Do not look directly into the laser beam with un-
protected eyes.
• Never look into the path of the beam.
• Never point the laser beam towards reecting sur-
faces and persons or animals. Even a laser beam
with a low output can cause damage to the eyes.
• Caution - methods other than those specied here
can result in dangerous radiation exposure.
• Never open the laser module. Unexpected exposure
to the beam can occur.
• The laser may not be replaced with a di󰀨erent ty-
pe of laser.
• Repairs of the laser may only be carried out by the
laser manufacturer or an authorised representative.
Residual risks
The machine has been built according to the state
of the art and the recognised technical safety re-
quirements. However, individual residual risks can
arise during operation.
• Health hazard due to electrical power, with the use
of improper electrical connection cables.
• Furthermore, despite all precautions having been
met, some non-obvious residual risks may still re-
main.
• Residual risks can be minimised if the „safety inst-
ructions“ and the „Proper use“ are observed along
with the whole of the operating instructions.

Scheppach HM254 Specifications

General

Laser guide	Yes
Product color	Blue, Grey
Sliding rails	-
Number of blade teeth	60
Input power	2000 W
Power source	AC
AC input voltage	220 - 240 V
AC input frequency	50 Hz
Idle speed (max)	- RPM
Cutting width (90°)	340 mm

Weight and Dimensions

Depth	820 mm
Width	480 mm
Height	410 mm
Weight	17560 g