4. INPUT/OUTPUT DATA
40
• Specific sensor selection: If a sensor is connected to the same NMEA2000
network, the sensor name appears in the [Input Device] list. Tap the sensor you
want to use.
Note: When the sensor to use as the data source is specified, automatic selec-
tion (when communication is lost or interrupted) is not available.
5. Repeat steps 3 and 4 to set up all data sources.
6. Tap the [u] at the top-right of the screen to close the menu.
4.4 How to select which NMEA2000 data to output
To set up which data is output to the NMEA2000 network, follow the procedure below.
1. Open the [Interface] menu.
2. Tap [Select Output NMEA2000 PGN]. The PGN list appears. The available PGNs
are listed below.
All PGNs, excluding 127505, are set to [ON] as the factory default.
3. Tap the ON/OFF toggle box to the far right of each PGN to select the required set-
ting.
• [ON]: Selected PGN is output to the NMEA2000 network.
• [OFF]: Selected PGN is not output to the NMEA2000 network.
4. Tap the [u] at the top-right of the screen to close the menu.
4.5 How to select which NMEA0183 sentence to out-
put
1. Open the [Interface] menu.
2. Tap [Select Output NMEA01083 Sentence]. The sentence list appears.
3. Tap the ON/OFF toggle box to the far right of each sentence to select the required
setting. Select [ON] to output the sentence.
Sentence Description
AAM Waypoint Arrival Alarm
APB Autopilot Sentence B
BOD Bearing Origin to Destination
BWR Bearing & Distance to Waypoint - Rhumb Line
DBT Depth Below Transducer
DPT Depth
GLL Geographic Position - Latitude/Longitude
126992 (System Time)
127258 (Magnetic Variation)
127505 (Fluid Level)
128259 (Speed)
128267 (Water Depth)
128275 (Distance Log)
129025 (Position, Rapid Update)
129026 (COG & SOG, Rapid Update)
129029 (GNSS Position Data)
129033 (Time & Date)
129283 (Cross Track Error)
129284 (Navigation Data)
129285 (Navigation - Route/WP Information)
130310 (Environmental Parameters)
130312 (Temperature)
130316 (Temperature, Extended Range)
130830 (Target Information)
130831 (Target Bottom Classification Data)
130832 (Target Fish Length)
4. INPUT/OUTPUT DATA
41
Note: If the total output baud rate of the selected sentences is too high, a notifica-
tion appears to inform you. Deselect sentences or adjust the baud rate.
4. Tap the [u] at the top-right of the screen to close the menu.
4.6 How to calibrate (offset) the sensors
If the data provided by your sensor is not accurate, you can offset the sensor data by
following the procedure below.
1. Open the [Interface] menu.
2. Tap [Calibration]. The sensor offsets appear.
3. At the sensor you want to offset, drag the slide bar, or tap the keyboard icon, to
set the offset value.
Note: The unit of measurement for some items is dependent on the language set-
ting and the unit selected in the [Settings] => [Units] menu. For the default settings
and setting options, see the menu tree at the back of this manual.
4. Tap the [u] at the top-right of the screen to close the menu.
GGA Global Positioning System Fix Data
GNS GNSS Fix Data
GSA GNSS DOP and Active Satellites
GSV GNSS Satellites in View
HDG Heading, deviation and variation
HDT Heading True
MTW Water Temperature
MWV Wind Speed and Angle
RMB Recommended Minimum Navigation Information
RMC Recommended Minimum Specific GNSS Data
RTE Routes RTE - Routes
THS True Heading & Status
TLL Target Latitude and Longitude
VHW Water Speed and Heading
VTG Course Over Ground & Ground Speed
WPL Waypoint Location
XTE Cross-Track Error, Measured
ZDA Time and Date
Target Information Target information (PFEC,SDmrk)
Target Bottom
Classification
Data
Bottom discrimination data (PFEC,SDtbd)
Target Fish
Length
Fish length information (PFEC,SDtfl)
Sentence Description
To Next Page
Loading...
Need help?
General
