0-7
CONTENTS
Introduction .....................................0-2
Machine description ........................0-4
Safety ..............................................1-1
General precautions ................................1-2
Precautions when preparing .................. 1-11
Precautions when starting .....................1-14
Precautions when operating ..................1-17
Precautions when stopping ...................1-27
Precautions when transporting ..............1-28
Precautions on maintenance .................1-30
Safety signs (decals) .............................. 1-42
Controls ...........................................2-1
Names of components ........................... 2-2
Covers ..................................................... 2-4
Ignition key .......................................... 2-4
Fuel filler port ....................................... 2-4
Engine hood ........................................ 2-5
Rear door ............................................ 2-5
Cab ......................................................... 2-6
Cab door ............................................. 2-6
Side Window ....................................... 2-8
Emergency exit .................................... 2-9
Fuse box ............................................. 2-9
Lift arm stopper ..................................... 2-10
Seat and seat belt ................................. 2-12
Seat .................................................. 2-12
Seat belt ........................................... 2-13
3-point seat belt (optional) ................. 2-13
Instrument cluster .................................. 2-14
Warning lamps ................................... 2-14
Indicators........................................... 2-15
Meters ............................................... 2-15
Multi-data display .............................. 2-16
Switches ............................................... 2-24
Ignition switch .................................... 2-24
Engine shutdown switch .................... 2-24
Horn button ....................................... 2-24
Float button ....................................... 2-25
Throttle controller ............................... 2-25
Multifunction buttons ......................... 2-26
Auxiliary hydraulic switches ................ 2-26
Travel speed button ........................... 2-28
Front wiper switch (optional)
Rear wiper switch (optional)
............... 2-29
Front light switch ...............................2-29
Tail light switch ................................... 2-29
ECO/Power mode select switch ........ 2-30
DPF manual regeneration/inhibit select
switch ................................................ 2-30
Auxiliary 1st flow rate select switch .... 2-32
Parking brake switch (TL12 optional) .. 2-32
Ride control switch
(TL10/TL12 optional)
.......................... 2-33
Aux. 2nd/14-pin connector select switch
(TL10/TL12 optional) .......................... 2-33
14-pin connector G/H select switch
(optional) ............................................ 2-33
Levers and Pedal ................................... 2-34
Safety Bar .......................................... 2-34
Throttle lever (TL10/TL12) .................. 2-34
Throttle pedal (optional) .....................2-34
Right control lever ..............................2-35
Left control lever ................................2-35
Accessories ........................................... 2-36
Air conditioner ................................... 2-36
External power socket ...................... 2-40
Interior light ........................................ 2-40
Mirrors ............................................... 2-41
Radio (for cab optional) ...................... 2-41
Auxiliary hydraulic lines (optional) ....... 2-48
Aux. 2nd lines (TL10/TL12 optional) ... 2-50
High-Flow Hydraulic System
(If equipped)
....................................... 2-52
Lift arm lower button (If equipped) ...... 2-53
Blow by heater lamp (If equipped) .........2-54
Active power control (If equipped) .........2-54
Operation .........................................3-1
Before starting operation .........................3-2
Getting on or off the machine ...............3-2
Walk-around inspection ....................... 3-2
Daily inspection .................................... 3-2
Starting and stopping the engine ............. 3-3
Before starting the engine .................... 3-3
Starting the Engine .............................. 3-4
Warming up the engine ........................ 3-5
Stopping the engine ............................ 3-6
Operating the machine ............................ 3-8
Lever pattern (ISO) ............................... 3-8
Lever pattern (H) (If equipped) .............. 3-9
Warming up the machine
(hydraulic oil)
...................................... 3-10
Inspection after warm-up ................... 3-11
Traveling the machine ........................ 3-12
Stopping travel .................................. 3-14
Operating the working equipment ...... 3-14
To Next Page
Loading...
Need help?
General
