27
I25 I24 I23 I22 I21 I20 I19 I18 I17 I16 I15 tr sv ro pt pl no nl it fr fi es en de cz
Service intervals
TASKI scrubber dryer machines are built to the highest quality standards and
have been checked for safety in the factory and by authorised inspectors.
Electrical and mechanical parts are subject to wear or aging if used for long
periods of time.
Service centre
Should you contact us due to a malfunction or for placing an order, please
always state the type, description and the serial number of your machine.
You can find this information on the name plate of your machine, and the
address of your nearest TASKI partner can be found on the last page of this
manual.
Cleaning or replacing the float (Overfilling protection for recovery tank)
Disassembly:
Malfunctions
Transport
Transport the machine in an upright position and remove the batteries for
transportation where necessary.
Make sure that the machine is securely fastened within the transportation
vehicle.
Refer to page 28 for the dimensions and weights.
Disposal
When it has reached the end of its operational life, the machine and its
accessories must be disposed of according to the national regulations. Your
TASKI partner can support you with proper disposal upon notification.
Batteries
The batteries must be removed from the machine before being disposed of
properly.
Used batteries must be disposed of in an environmentally appropriate way in
accordance with the EU guidelines 2006/66/EEC.
• In order to ensure operational reliability and
availability for use, the service must be carried
out when the service indicatior lights up (factory
setting 550 working hours) or at least once a
year.
Shorter intervals are necessary in case of rough environments or special
conditions of use and/or inadequate maintenance.
• Switch the machine off using the keyswitch and remove the key.
• The yellow suction filter can be simply removed
together with the float (quick-release
connection).
• Clean it with water using a brush (let it dry out
well).
• Brush the yellow suction filter with a soft brush
or remove the fluff with a cloth.
Malfunction Possible causes Troubleshooting page
Machine does not
run
Maschine switched off
• Switch on the
keyswitch.
22
Battery/mains
unit malfunction
(display on
control panel)
Discharged batteries
• Recharge batteries
22
Batteries/battery
charger defective
• Call for technical
assistance
Batteries not
sufficiently
charged
Power cord not
plugged in or
defective
• Plug in the power cord
• Call your Service
Partner
Batteries or battery
charging unit
defective
• Call your Service
Partner
Brush does not
turn
Motor runs but not
tool
• Call for technical
assistance
Poor vacuum
performance
Floor remains
wet
Soiled solution
not picked up
The float closes the
inlet opening at the
suction unit (overfill
protection for
recovery tank)
• Check the recovery
tank is not full
25
• Check that the float is
functioning correctly.
27
Squeegee not on the
floor
• Lower the squeegee.
25
Suction hose not
connected
• Connect suction hose
24
Check the seal on the
tank lid for cracks/dirt
• Clean the seal, or
replace if defective
Suction filter blocked
• Remove the blockage
Hose or nozzle
blocked (e.g. by
pieces of wood or
residual material)
• Remove the blockage
The blades do not
adjust well to the floor
consistancy
• Clean the squeegee
• Change/turn the
blades
• Check that the
squeegee suspension
is functioning correctly
• Squeegee adjustment
Dirt sieve full (yellow)
• Remove the dirt sieve
• Empty the dirt sieve
and rinse it under
running water.
26
Insufficient output
of cleaning
solution
Solution tank empty
• Fill the solution tank
24
Solution tank filter
blocked
• Clean solution tank
filter
26
Foam or liquid
leaking from the
machine
Float malfunction
• Turn off the suction
aggregate
• Check that the float is
functioning correctly.
22
27
• Check the suitability of
the chemical product
for use with scrubber
dryer machines.
To Next Page
Loading...
Need help?
General