10
2. Push the module in as far as it will go.
3. Turn on the TV and wait for the common interface
function to be activated. This may take several
minutes.
Note: Do not remove the common interface module
from the slot. Removing the module will
deactivate the digital services.
Accessing common interface services
After inserting and activating the common interface
module, press
on the remote control, select
Channel > Common interface and press OK/► to
enter.
This menu option is only available if the common
interface module is correctly inserted and activated. On-
screen applications and content are provided by your
digital TV service operator.
Note: This feature is only available under DTV source.
Using Subtitles
You can enable subtitles for each TV channel.
Subtitles
are broadcast via Teletext or DVB-T/DVB-C digital
broadcasts. With digital broadcasts, you have the
additional option of selecting a preferred subtitle
language.
Turning on/off subtitles
1. Press on the remote control, select Channel >
Subtitle and press OK/► to enter.
2. Select the Subtitle option, press OK/► to enter,
press ▲/▼ to select On or Off and press OK to
conrm.
3. Press EXIT or
to close the menu.
Enabling subtitle languages on digital TV
channels
1. Press on the remote control, select Channel >
Subtitle > Digital subtitle language 1st and press
OK/► to enter.
2. Press ▲/▼ to select a subtitle language as your
preferred language and press OK to conrm.
3. Press ▲/▼ to select Digital subtitle language 2nd
and press OK/► to enter.
4. Press ▲/▼ to select a secondary subtitle language
and press OK to conrm.
5. Press EXIT or
to close the menu.
Shortcut operation: Press SUBT. on the remote
control
to directly select a subtitle language available for the
selected digital TV program.
Note: You should set Subtitle ON.
Installing Channels
This section describes how to search and store
channels
automatically. This may be done in any of the cases
below:
- you have skipped the channel installation step in the
initial setup;
- you are prompted that there are no channels in TV
mode;
- you want to update your channels.
1. In TV mode, press
on the remote control and
select Channel > Channel scan. Press OK/► to
enter.
2. The TV installs and arranges channels according
to your country. Press ▲/▼ to select Country, and
press OK/► to enter. Enter the default password
1234 or your own password in case you have
changed the password in the System > Lock menu.
Press ▲/▼ to select your country and press OK to
confirm.
3. Press ▲/▼ to select Automatic search and press
OK/► to enter.
4. Press ▲/▼ to select Tuner mode and press ◄/► to
select Cable, Antenna or Satellite. (Note: Satellite
option is available only in selected models.)
5. Press ▲/▼ to select other options to configure.
6. After configuration is completed, press ▼ to select
Search and press OK to start scanning channels.
7. The channel search may take a few minutes. After
the automatic search, channels are arranged in a
preset order. If you wish to hide or swap channels,
press
on the remote control, select Channel >
Channel organizer and press OK/► to enter.
Common Interface
(* not available for some models)
Encrypted digital TV channels can be decoded with a
common interface module and a card provided by a
digital TV service operator.
The common interface module may enable several
digital services, depending on the operator and services
you choose (for example, pay TV). Contact your digital
TV service operator for more information about services
and terms.
Using the common interface module
WARNING: Switch off your TV before inserting a
common interface module. Be sure to follow the
instructions described below. Wrong insertion of
a common interface module may damage both the
module and your TV.
1. Following the directions printed on the common
interface module, gently insert the module into the
common interface slot on the TV.
Chapter 4 Using more of your TV
To Next Page
Loading...
Need help?
General
