Technics SC-DV250 User Manual

L
ee
Refer to iltustratlons BY and §J on page 17 of the illustrated booklet.
A Batteries
@insert so the polas (+ and —) match those in the remote control.
Do not use rechargeable type batteries.
Do not;
mix old and new batteries.
uso differant types at the same time.
heat or expose to flame.
take apart or short circuit.
*attempt to recharge alkaline or manganese batteries,
use batteries if the covering has been peeled off.
®keep together with metallic objects such as necklaces,
Mishandling of batteries can cause electrolyte leakage which can damage
itams the fluid contacts and may cause a fire.
{f electrolyte leaks from the batteries, consult your dealer.
Wash thoroughly with water if electrolyte comes in contact with any part of
your body.
Remove if the remote control is not going to be used for a long period of
time. Store tn a cool, dark place.
Replace if the unit does not respond to the remote control even when held
close to the front panel.
Aim at the sensor, avoiding obstacles, at a maximum range of about 7 me-
ters directly in front of the unit.
Keep the transmission window and the unit's sensor free from dust.
Operation can be affected by strong light sources, such as direct sunlight,
and the glass doors on cabinets,
Do not;
put heavy objects on the remote control.
‘take the remote control apart.
spill tiquids onto the remote control,
naan
era
Se
Refer to Illustration [J on page 17 of the illustrated booklet.
Rie
This is a 24-hour clock.
The example shows how to set the clock for 16:25 (4:25 p.m.).
1 Press [¢/I] to turn the unit on.
2 @ Press [CLOCK/TIMER] to display “CLOCK”.
Each time you press the button:
CLOCK @PLAY— OREC— Original display
t |
@ Within 5 seconds
Press [SET].
@ Press [TUNING (v or ~)] to set the time.
The time display can ba changed in one minute units by tapping
the buttons, and quickly by holding down the buttons.
@ Press [SET].
The time Is set and the original display is restored.
Displaying the clock
Press [CLOCK/TIMER].
The clock is shown for about 5 seconds.
Reset the clock regularly to maintain accuracy.
Refer to the illustration on page 14 of the illustrated booklet.
Remote control only
Change the setting to suit the aspect ratio of your television.
The menu language fs set to English, but you can change it to
other languages (™ page 25, Display—-Menu Language). English is
used in the examples.
Preparation
Turn on the television and select the appropriate video input on the televi-
sion to suit the connections for the player.
1 Press [¢)] to turn the unit on.
2 Press [DVD] to select “DVD” as the source.
3 While stopped
Press [SHIFT]+[SETUP] to display the initial set-
tings screen.
Press [<, >] to select the Video tab.
Press [A, WV] to select “TV Aspect” and press
[ENTER].
Press [A, W] to select the item and press
[ENTER].
4:3 Pan&Scan (Factory preset)
Select if you have a regular television and to view 16:9 software® in
the pan and scan style,
ah
4:3 Letterbox
Select if you have a regular television and to view 16:9 software in
the letterbox style.
016:9
Select if you have a widescreen television.
“16:9 software prohibited from being shown in the pan and scan stylo
will appear in the letterbox style despite the setting here.
The Video menu is shown.
Press [RETURN] to end the settings.
7
To return to the previous screen
Press [RETURN].
For your reference
DVDs are recorded in a variety of aspect ratios. You can change the way
software is shown on a regular television (4:3) with the above operation. If
you have a widescreen television (16:9), use the television's picture
modes.
Control guide and preparatory steps |
| RQTS948,

Technics SC-DV250 Specifications

General

Brand	Technics
Model	SC-DV250
Category	Stereo System
Language	English