Technics SL-Q2 User Manual

Specifications
@ General
Power supply: ~110-120/220-240V, 50 or 60 Hz
Power consumption: 7.5W
Dimensions: 43.0 X 13.0 x 37.5 cm
(WxHxD)
(16-59/64"
x
5-7/64"
x
14-49/64")
Weight: 6.9 kg (15.2 Ib.)
@ Turntable section
Type: Automatic turntable
Auto return
: Auto stop
Drive method: Direct drive
Motor: Brushless DC motor
Turntable platter: Aluminum die-cast
Diameter 31.2 cm (12-9/32 inches)
Turntable
speeds:
33-1/3
rpm
and
45
rpm
Starting
torque:
1
kg-cm
(0.87
Ib:in)
Build-up characteristics: 0.9 s, from standstill to 33-1/3 rpm
Speed change due to
load
torque:
0%
within
0.7
kg-cm
(0.61
Ib-in)
Speed
drift:
Within
+0.002%
Wow
and
flutter:
0.012%
WRMS*
0.025% WRMS (JIS C5521)
+0.032% (IEC98A Weighted)
‘This
rating
refers
to
turntable
assembly
alone,
excluding
effects of record, cartridge or tonarm, but including platter.
Measured
by
obtaining
signal
from
built-in
frequency
gen-
erator of motor assembly.
Rumble:
—56
dB
(IEC
98A
Unweighted)
—78
dB
(IEC
98A
Weighted)
@ Tonearm section
Type:
Universal
tonearm
Effective
length:
230
mm
(9-1/16")
Overhang 15 mm (19/32")
Friction:
Less
than
7
mg
(lateral,
vertical)
Effective
mass:
12
g
(without
cartridge)
Tracking
error
angle:
Within
2°32'
at
the
outer
groove
of
30
cm
(12")
record
Within
0°32’
at
the
inner
groove
of
30
cm
(12")
record
Offset angle: 22°
Stylus pressure
adjustment range: 0—2.5g
Applicable cartridge
weight range: 6—9.5g
13.5—17
g
(including
headshell)
(with
shellweight)
3—6.5
g
10.5—14 g (including headshell)
Headshell weight: 7.59
@ Cartridge section
Model No.: EPC-207C
Type: Moving magnet
Frequency response: 20 Hz to 25 kHz
20 Hz to 15 kHz +2 dB
Output voltage: 3 mV at 1 KHz
5 cm/s. zero to peak lateral velocity
(8.5 mV at 1 kHz, 10 cm/s. zero to
peak 45° velocity [DIN 45 500])
Channel separation: 25 dB at 1 kHz
Channel balance: Within 2 dB at 1 kHz
Compliance (dynamic): 10 x 10° cm/dyne at 100 Hz
Stylus pressure: 1.75 0.25 g (17.5 + 2.5mN)
Load impedance: 47 kQ to 100 kQ
Weight: 5.6 g (cartridge only)
Replacement stylus: EPS-207ED (Elliptical stylus)
Specifications subject to change without notice.
Weight and dimensions shown are approximate.
For longer and safer use
of this unit
In order to receive the best service from this unit, and for the
safest operation, carefully read the following information.
‘Power source
It is very dangerous to use this unit at a voltage which is
different from the rated voltage.
There is danger of combustion if the unit is connected to a
power source which is different from the rated voltage.
Be very careful concerning this point.
Direct current cannot be used.
There are some places, such as ships, where direct current
is used as the power source, Before connecting the unit,
confirm the power source.
Connection of power cord
Be sure to never touch the power cord with wet hands because
there is danger of electric shock. This is true, of course, of all
electric equipment.
Do not pull the power cord.
Never pull the power cord to disconnect it. Always pull the
plug only.
Location of unit
Choose a place which is not in direct sunlight.
Select a place which will assure good ventilation.
Never place heating equipment nearby.
Be sure to keep stoves and other sources of heat away from
this unit, because heat radiated by such equipment may cause
deformation of plastic parts or damage the cabinet, or, at
worst, cause a fire.
Especially for families with children
Take care that no small items, such as metal objects, are put
inside this unit.
In addition, children should be especially warned not to put
anything into the ventilation holes, such as toys or a screw-
driver, because these things may cause an electric shock or
result in a malfunction of the unit.
tf water spills on the unit
If water should happen to spill on the unit, from an overturned
vase for example, there is danger of fire or electric shock:
Disconnect the power plug from the electric outlet imme-
diately, and contact the store from which the unit was pur-
chased,
Reconstruction can cause accidents
Absolutely never try to remodel, reconstruct or repair this
unit yourself, Do not attempt to touch any internal parts be-
cause to do so may result in an electric shock or other ac-
cident.
Be sure the power is off.
After you have finished using this unit, check once more to
be sure that the power is off. If the unit is left with the power
on for a long period of time, it may not only be damaged,
thus shortening its useful life, but may also lead to a danger- *
ous accident.

Technics SL-Q2 Specifications

General

Drive System	Direct drive
Speeds	33 1/3 and 45 rpm
Wow and Flutter	0.025% WRMS
Signal-to-Noise Ratio	78dB (DIN-B)
Effective Length	230mm
Overhang	15mm
Platter	Aluminum die-cast
Tonearm Type	Static Balanced
Rumble	-78dB