To Next Page

To Previous Page

Speciﬁcations

Table 9 : Amplit

ude and RF ﬂatness (excluding mismatch error)

Characteristic Description

Reference level setting range, nominal –170 dBm to +40 dBm, 0.1 dB step, (Standard RF input)

Frequency response (18 °C to 28 °C)

10 MHz to 32 M

Hz, LF Band

±0.2 dB

10MHzto3GH

±0.35 dB

3GHzto6.2

GHz

(RSA5106B/5115B/5126B)

±0.5 dB

6.2 GHz to 15 GHz

(RSA5115B/5126B)

±1.0 dB

At 10 dB RF

attenuator setting

15 GHz to 26.5 GHz

(RSA512

6B)

±1.2 dB

10 MHz to 32 MHz, LF Band

(RSA510

3B/5106B)

±0.5 dB

10 MHz t

o3GHz

±0.5 dB

3GHzto

6.2 GHz

(RSA5106B/5115B/5126B)

±0.7 dB

6.2 GHz to 15 GHz

(RSA5115B/5126B)

±1.0 d

At 10 dB RF

attenuator setting,

With Preamp ON

15 GHz to 26.6 GHz

(RSA

5126B)

±1.2 dB

All RF attenuator

set

tings

1 Hz to 100 Hz, LF Band ±0.7 dB

8 RSA5100B Series Technical Reference

Table of Contents5
General Safety Summary10
Preface13
Related Manuals13
Specifications15
Table 1: Specification Categories15
Performance Conditions16
Electrical Specifications16
Table 2: Frequency16
Table 3: Phase Noise17
Table 4: Integrated Jitter19
Table 5: RF Input19
Table 6: Maximum Input Level20
Table 7: Input Attenuator20
Table 8: Analog Sweep21
Table 9: Amplitude and RF Flatness (Excluding Mismatch Error)22
Table 10: Noise and Distortion24
Table 11: Channel Response - Amplitude & Phase Flatness (Standard/Option B40)28
Table 12: Channel Response - Amplitude & Phase Flatness (Option B85)29
Table 13: Channel Response29
Table 14: Channel Response after Cal/Norm (Center Frequency 200 Mhz)30
Table 15: Channel Response after Cal/Norm (>6.2 Ghz < Center Frequency ≤15/26 Ghz) (RSA5115B/5126B)30
Table 16: Channel Response after Cal/Norm (Center Frequency 65 Mhz) (RSA5115B/5126B)31
Table 17: Pulse Measurements, Typical31
Table 18: Impulse Response38
Table 19: Test Parameters for Pulse to Pulse Carrier Phase/Frequency39
Table 20: Spurious Response39
Table 21: Spurious Response with Signal at Center Frequency (Offset ≥400 Khz)41
Table 22: Spurious Response with Signal at Center Frequency (10 Khz ≤ Offset ≤ 400 Khz)41
Table 23: Spurious Response with Signal at Input Other than Center Frequency41
Table 24: Higher RF Order Spurious Response42
Table 25: Spurious Response with Signal at Input (if Feed-Through)42
Table 26: Acquisition42
Table 27: Amplitude Vs. Time44
Table 28: Trigger45
Table 29: Resolution Bandwidth Filter (SA Mode)53
Table 30: Range and Settable RBW (SA Mode)54
Table 31: Resolution Bandwidth Filter (Time-Domain Mode)54
Table 32: Range and Settable RBW (Time-Domain Mode)55
Table 33: Video Bandwidth Filters55
Table 34: Preamp (Option 50/51)56
Table 35: Digital IQ Output56
Table 36: 28 Volt Noise Source Drive Output56
Electrical Functional Specifications57
Table 37: Zero Span Analog Output (Opt. 66)57
Physical Characteristics76
Safety77
Certifications and Compliances77
Environmental Characteristics77
Digital IQ Output Connector Pin Assignment (Option 65 Only)78
Figure 1: Digital IQ Output Connector Pin Assignment78
Digital IQ Output Timing82
Figure 2: IQ Timing83
Performance Verification85
Prerequisites85
Required Equipment85
Preliminary Checks87
Warranted Characteristics Tests89
Frequency Accuracy89
Figure 3: Connections for Reference Frequency Output Accuracy Check89
Figure 4: Power Meter Setup90
Figure 5: Power Meter Calibration90
Figure 6: Equipment Connections for Ref out Power Level Check91
Figure 7: Equipment Connections for Ref in Power Level Check91
Phase Noise (Instruments with Option 11)92
Figure 8: Equipment Connections for Phase Noise Checks93
Phase Noise (Instruments Without Option 11)94
Figure 9: Equipment Connections for Phase Noise Checks95
Amplitude99
Figure 10: Equipment Connections for RF Flatness Check99
Figure 11: Equipment Connections for Low Frequency (LF) Input Path Accuracy Check109
Figure 12: Equipment Connections for RF Flatness (Frequency Response) 10 Mhz to 26.5 Ghz Check112
Noise and Distortion126
Figure 13: Equipment Connections for Third Order Intermodulation Distortion Check126
IF Flatness (Channel Response)134
Figure 14: Equipment Connections for if Flatness Check134
Spurious Response138
Figure 15: Equipment Connections for Image Suppression Check140
Figure 16: Equipment Connections for Signal Spurious Check142
Figure 17: Equipment Connections for Zero-Span Output Check147
Test Record148

Brand	Tektronix
Model	RSA5106B
Category	Measuring Instruments
Language	English

Tektronix RSA5106B Technical Reference

Table of Contents

Other manuals for Tektronix RSA5106B

Questions and Answers:

Tektronix RSA5106B Specifications

Related product manuals