Note:
•
To
use this function:
- Set Speclker Preference
to
Audio
Receiver
in
the
REGZA-LINK Setup menu
- Confirm that a connected
REGZA-L1NK
device
(such as
DVO
player, etc)
is
selected for
the
Audio Receiver input source.
•
You
can also use this function when the
audio
receiver is
connected
to the
TV's
DIGITAL
AUDIO
OllT
terminal (not HOMI connection).
In
this case, select a digital audio
input
mode
on the
Audio
Receiver
• These functions
depend
on the device
connected.
Other
RE('l,A·LlNK®
functions
When
the
Enable
REGZA-L1NK
and
each
item
in
the
REGZA-L1NK
SEltUP
menu
are
set to
On,
the
following
functions
will be
enabled.
To
set
the
REGZA-LINK® Setup:
1
From
the
Setup
menu,
highlight
REGZA-L1NK
Setup
and
press
8.
2
Press
or
.....
to
highlight
Enable
REGZA·L1NK.
3
Press
or
~
to
select
On.
Note:
If you select
Enable
REGIA-LINK
Off,
the
other items will
be
grayed
out.
4
Press
....
or
.....
to
highlight
the
REGZA-L1NK
Setup
item
you
want
to use,
and
press
....
or
~
to
select
On
or
desired
mode.
•
TV
Auto
Input
Switch:
On/Off
•
TV
Auto
Power:
On/Off
•
Device
Auto
Standby:
On/Off
• Speaker Preference: TV Speakers/Audio Receiver
5 To
save
the
new settings,
highlight
Done
and
press
8.
To revert
to
the
factory
defaults,
highlight
Reset
and
press
8.
Note: When you turn on the
Audio
Receiver,
change
its input source,
or
adjust
the
sound
volume, the
sound
will
be
output from the audio
receiver's speakers even
if
TV
Speakers
has
been selected.
Turn
the
TV
off
and
on again
to
output the
sound
from the
TV
speakers.
TV
Auto
Input
Switch
TV
Auto
Power
Device
Auto
Standby
Speaker
Preference
Ifa connected HDMI device starts
playing video or audio, the TV will
automatically switch
to
the appropriate
HDMI input.
If
a REGZA-LINK device
is
tumed on,
the TV tums on automatically.
If
the TV
is
tumed off the TV will send
a message
to
turn off
all
of
the REGZA-
LINK devices connected to the
TV
From this item, you can set your audio
output preference to the
TV
speakers
or the audio receiver speakers. When
this item
is
set to Audio Receiver,
the TV remote can be used to adjust
or
mute the volume
of
the audio.
This item will be grayed out unless
a REGZA-LINK compatible audio
receiver is connected.
Displaying
TV
status
information
To
display TV
status
information using
RECALL:
Press
I
RECAliJ
on
the
remote
control.
The
following information will display
(if
applicable):
•
Current
input
(ANT/CABLE,
VIDEO,
etc.)
•
If
ANT/CABLE
is
the current input, either "CABLE"
(for cable TV)
or
"ANT" (for over-the-air broadcasts).
• Channel number
(if
in
ANT/CABLE
mode)
• Channel label
(if
applicable)
• Digital signal strength indicator (bar graph
in
lower
right corner
of
box; for ATSC signal only)
• Stereo, Mono
or
SAP
audio status (when HDMI input
mode, Dolby Digital
or
PCM)
• Video resolution
• Aspect ratio
of
incoming video signal (4:3
or
16:9)
• V-Chip rating status
• GameTimer
(if
set)
:_,.
t··t1Mil'M""""am-kb4t1
W
':
.
To
close
the
RECALL
screen:
Press
I
RECAll
Iagain.
(continued)
49
I
To Next Page
Need help?
General
