Stopping
Cleansing
"Front cleansing"
Serves as a bidet for
ladies.
"Rear soft cleansing"
Cleanses your rear with
mild water pressure.
"Stopping"
Stops the operation.
The setting changes between "ON" and
"OFF" each time the button is pressed.
"Rear cleansing"
Cleanses your rear.
"Water pressure adjustment"
Basic Operations
Note
Sitting back on the toilet seat
makes it easier to adjust the wand
position and to reduce splashing.
*1 Remote control transmitter (Front side, Top side)
"Pulsating cleansing"
Cleanses with the water pressure
pulsating between soft and strong.
"Oscillating cleansing"
The wand moves back and forth
to cleanse your rear thoroughly.
*1
*2 Except SW4047T60 and SW4049T60.
16 17
Operate the controls on the remote control; a beep sounds when the main unit
receives the signal.
Personal setting lock
You can store your preferred "Wand position", "Water
pressure" and "Warm water temperature" settings.
●
To store a settings
While cleansing is in progress, set your preferred "Wand position",
"Water pressure" and "Warm water temperature" and then press
and hold
or for 2 seconds or longer.
●
To use
Press
or , and then press the button for the cleansing you want
to use.
The "Wand position" and "Water pressure" lamps will light up for about
10 seconds in their set positions, and the "Warm water temperature"
display switches.
A light will also fl ash for about 10 seconds
to indicate the current setting when any of
the cleansing buttons (rear cleansing, rear
soft cleansing, front cleansing) are pressed.
You can adjust the washing
position to 5 different points
between the front and the rear,
using the [▲] and [▼] buttons.
After you press the "Wand position
adjustment" button, the set position
will light for 10 seconds.
"Wand position adjustment"
You can adjust the water pressure
to one of fi ve levels.
([-] Softer, [+] Stronger)
After you press the "Water pressure
adjustment" button, the set position
will light for 10 seconds.
A light will also fl ash for about 10 seconds
to indicate the current setting when any of
the cleansing buttons (rear cleansing, rear
soft cleansing, front cleansing) are pressed.
●
Functions that operate when
a button is pressed during
"Rear cleansing", "Rear soft
cleansing" or "Front cleansing".
Flushing
*2
"Full fl ush"
Performs a full fl ush.
"Light fl ush"
Performs a light fl ush.
Remote control back side
"Timer energy
saver"
"Power ON/OFF"
"Auto energy
saver"
"Auto energy
saver+"
Adjust temperatures (Page 20) Saving energy (Page 24)
"Wand cleaning"
To clean the wand
with it extended.
(Page 28)
Pressing it about 3 seconds or
longer turns the power on/off.
•
If the remote control is secured to
prevent theft (Page 15 Step 2-
2)
Temperatures Energy Saver
This section is an overview of the settings that can be confi gured with the remote control.
See the corresponding pages for the detailed descriptions.
"Toilet seat
temperature"
"Warm water
temperature"
For changing Settings (Page 32)
Auto functions
*2
"Auto fl ushing"
"Setting
confi rmation"
The current setting
can be discerned
from the LEDs.
Low battery warning
mark
(Page 36)
Cleans the wand with "ewater+".
The wand can be automatically
cleaned when you use the
cleansing functions (Rear cleansing,
Front cleansing, etc.). (Page 18)
"Wand CLEAN"
The setting changes between
and
each time the is pressed.
Operation
To Next Page
Loading...
Need help?
General
