Trane S8B1A040M3PSCA/C User Manual

50
S8XB-SVX001-1C-EN
Integrated Furnace Control Menu
I
dL
STATUS MENU
Err
ACTIVE ERRORS
Ht tp5
Example
Gas Heat
Example
Tap 5
E3.1
Example
Pressure Switch Error
L6F
LAST 6 FAULTS
E3.1 E04
Example
Pressure Switch Error
Example
Open Limit Switch Error
CR
Control Release #
Example
So!ware Version #
Example
ODU
Outdoor Stages
1-1 2-1
HOD
Heat Off Delay
100 060
C
F
Con
$
nuous Fan Tap
CF.1
Example
Tap #
COP
Compressor Opera$on
Speed Tap
Ex
am
pl
e
Tap #
Example
T
ap #
S8B1 - S8X1
Control System Menu Single Stage OD
140
CLEARING THE LAST6 FAULTS:
To clea
r
the
stored faults, scroll to the last 6 faults menu (L6F),
enter th
e
m
enu by scrolling to the right and hold the
“Op$on” k
ey for at least 5 seconds. Release and a set of 3
dashes will be s
een 3 $mes. This confirms the faults have
been cleared.
SETTING UP YOUR SYSTEM:
To change any factor
y
def
ault value, first remove any “call”
from the furnace and a
l
low
all fan off delays to finish. (IDL
should be seen on the display
)
Scroll to the selected Menu it
em by momentarily depressing
the “MENU” key and then depr
ess the “OPTION” key to the
desired se&ng. Then momentarily
depress the “MENU” key
again to save the change.
180
C1.7 C1.1
C1.2 C1.3 C1.4
HtP
Hea$ng Speed Tap
H1.
5 H1.1
001
H1.2
H1.6H1.3
Single Stage
Example
2 stage 1 compressor
SELECTING GAS HEAT FAN SPEEDS:
Airflow can be adjusted while the unit is running.
Scroll to the HTP menu and momentarily push the OPTION key. Tap #5 is the
default se&ng for all models. When selec$on is made, momentarily push the
ME
NU
k
ey
to save.
I
f the temperature rise i
s
too hig
h
, i
ncr
ease airflow. If the temperature ris
e
too
low,
de
crease a
irflo
w
.
N
OTE
:
Tap
9
is not available f
or
gas
h
ea$n
g.
r
u
n
Run
Test Mode
C1.
5 C1.6 C1.8 C1.9
H1_7
H1.8
H1.4
ORN
LED Orienta$on
UP
dn
Default Airflow Taps
Gas Heat = Tap 5
OD
U
M
e
nu 1-1
Coo
li
n
g
/ HP = Tap 7
SELECTING COOLING/HP FAN SPEEDS for 1-1 ODU:
Airflow can be adjusted while the unit is running.
Scroll to the COP menu and momentarily push the OPTION key. Tap 7 is the
default se&ng for all models. When selec$on is made, momentarily push the
MENU key to save.
Note:
Do not adjust C0F above Tap 1.
Designated Gas Hea$ng Airflow Taps
S8*1A040M3PSC
(1-8)
S8*1B040M2PSC
(
1
-8)
S8*1B060M4PSC
(1-7)
S8*1B080M4PSC (1-6)
S8*1C080M5PSC (1-8)
S8*1C100M5PSC (1-8)
S8*1D120M5PSC (1-7)
O
O
COd
Cooing Off De
lay
000
090
180
seconds
Example
Note:
S8B1 does not have 0dU menu item.
seconds
Example
See R
un Test Menu

Trane S8B1A040M3PSCA/C Specifications

General

Brand	Trane
Model	S8B1A040M3PSCA/C
Category	Furnace
Language	English