EasyManuals Logo
Home>Visonic>Security Sensors>Next K9-85 MCW

Visonic Next K9-85 MCW User Manual

Visonic Next K9-85 MCW
4 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Page #1 background imageLoading...
Page #1 background image
DE3592 1
NEXT
®
K9-85 MCW
Wireless PowerCode Pet-Immune PIR Detector
Installation Instructions
1. INTRODUCTION
The NEXT K9-85 MCW is a pet-immune microprocessor-controlled
wireless digital PIR detector, designed for easy installation, free of
vertical adjustment. It features a cylindrical lens with uniform
detection sensitivity throughout its operating range, up to 12 meters
(40 ft), with immunity to pets weighing up to 38 kg (85 lb).
NEXT is a registered mark of Visonic Ltd.
The
advanced True Motion Recognition™ algorithm (patented)
allows the NEXT K9-85 MCW to distinguish between the true
motion of an intruder and any other disturbances which may cause
false alarms. In addition, Target Specific Imaging™ (TSI)
technology is employed for distinction between human beings and
pets.
An on-board motion event jumper determines whether 1 or 2
consecutive motion events trigger an alarm.
The NEXT K9-85 MCW includes the following features:
Incorporates a fully supervised PowerCode transmitter
Patented sophisticated motion analysis algorithm - True Motion
Recognition (TMR™)
Sophisticated frequency domain digital signal processing
No vertical adjustment is needed
Programmable motion event counter
After detection, the detector disarms itself to save battery
power. It rearms (reverts to the ready state) if there is no
subsequent detection throughout the following 2-minute period.
An optional version provides better protection for systems
compliant with DD243. After initial detection, the detector is
capable of 7 additional detections for a period of 5 minutes.
Further detection is possible only if no movement occurs during
the following 2 minutes. The detector will revert to the initial
state if there is no movement for an additional 5 minutes.
Very low current consumption
Microprocessor-controlled temperature compensation
Sealed chamber protects the optical system
Front cover tamper switch
Back tamper switch (option)
White light protection
Elegantly styled, sturdy case
Figure 1. General View
Figure 2. Inside View
For UL installations:
a. The detector is for use with UL listed control unit PowerMax+ only.
b. Pet immunity has not been evaluated by UL.
2. SPECIFICATIONS
OPTICAL
Detector Type: Dual element low-
noise pyroelectric sensor.
Lens Data
No. of Curtain Beams: 9
Max. Coverage: 12 x 12 m (40
x 40 ft) / 90°
Pet Immunity: Up to 38 kg (85 lb).
ELECTRICAL
Internal Battery: 3V Lithium battery,
type CR-123A. For UL installations,
use Panasonic or Sanyo only.
Nominal Battery Capacity:
1450 mA/h.
Standby Current Drain: approx.
0.025 mA.
Transmit Current Drain: 20 mA
(including LED).
Battery Life (with LED on):
Typically over 3 years.
Figure 3.
Coverage Pattern
Battery Power Test: Performed immediately upon battery
insertion and periodically after every several hours.
FUNCTIONAL
True Motion Event Verification: 2 position selector - 1 (OFF) or
2 (ON) motion events.
Alarm Period: 3 seconds.
Visual Indications:
LED Lights for about 3 seconds upon transmission of alarm &
tamper messages and upon motion detection in the walk test
mode.
LED Flashes during the power-up stabilization period, or after
restoring (pressing) the tamper switch.
LED Does not light upon transmission of supervision
messages.
Rearm Timer: Rearms the detector 2 minutes after the last alarm.
Timer disabled in the walk test mode – not applicable for the
DD243 version (see section 1).
WIRELESS
Frequency (MHz): 315 (U.S. version), 433.92, 868.95, 869.2625
or other frequencies according to local requirements.
Transmission Sequence: 3 data bursts at variable intervals
within 3 seconds.
Encoding: 24-bit ID, over 16 million possible combinations.
Total Message Length: 36 bits.
Tamper Alert: Reported when a tamper event occurs and in any
subsequent message, until the tamper switch is restored.
Supervision Message: Signaling at 60 minutes interval (U.S.
version), 15 minute interval (UK version) or according to local
standards.
MOUNTING
Height: 1.8 - 2.4 m (6 - 8 ft). Recommended height up to 2.1 m (7 ft)
Installation Options: Surface or corner.
ACCESSORIES:
BR-1: Surface mounted swivel bracket, adjustable 30° down and
45° left/45° right.
BR-2: BR-1 with a corner adapter
BR-3: BR-1 with a ceiling adapter

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Visonic Next K9-85 MCW and is the answer not in the manual?

Visonic Next K9-85 MCW Specifications

General IconGeneral
BrandVisonic
ModelNext K9-85 MCW
CategorySecurity Sensors
LanguageEnglish

Related product manuals