September 2005
5-1
CC C123/128,WC M123/128,WC Pro123/128,CC 133,WC 133,WC Pro133
Parts-list
1st Version
5 Parts List
Overview
Introduction...................................................................................................................... 5-3
Subsystem Information.................................................................................................... 5-4
Symbology.......................................................................................................................5-5
Parts Lists
1. Drives
PL 1.1 Main Drive........................................................................................................... 5-9
2. Paper Transportation
ray, Feeder 1/2 Assembly................................................................................. 5-10
ray 1/2............................................................................................................... 5-11
eeder 1/2 Assembly.......................................................................................... 5-12
egistration......................................................................................................... 5-13
ertical Transport Cover..................................................................................... 5-14
ransfer Cover Assembly ................................................................................... 5-15
/H Upper Chute Assembly ................................................................................ 5-16
/H Upper Cover Assembly ................................................................................ 5-17
OS .................................................................................................................... 5-18
graphics/Development
RU, Toner Cartridge......................................................................................... 5-19
oner System...................................................................................................... 5-20
r
user Unit ........................................................................................................... 5-21
xit...................................................................................................................... 5-22
xit 1................................................................................................................... 5-23
/H Upper Chute Assembly ................................................................................ 5-24
ray Guide Assembly.......................................................................................... 5-25
/H Upper Chute Assembly ................................................................................ 5-26
ray Guide Assembly.......................................................................................... 5-27
7. MPT
PL 7.1 MPT Assembly.................................................................................................... 5-28
PL 7.2 Lower Frame Assembly ...................................................................................... 5-29
PL 7.3 MPT Tray Assembly............................................................................................ 5-30
8. Duplex
PL 8.1 Duplex Unit ......................................................................................................... 5-31
PL 8.2 Inner Chute Assembly......................................................................................... 5-32
9. Electrical Components
PL 9.1 Electrical ............................................................................................................. 5-33
PL 9.2 ESS.....................................................................................................................5-34
PL 9.3 FAX Unit.............................................................................................................. 5-35
PL 9.4 Wire Harness ...................................................................................................... 5-36
10. Covers
PL 10.1 Cover-Front, Left............................................................................................... 5-37
PL 10.2 Cover-Rear, Right............................................................................................. 5-38
11. IIT
PL 11.1 Platen/Cover ..................................................................................................... 5-39
PL 11.2 Control Panel .................................................................................................... 5-40
PL 11.3 Platen Glass...................................................................................................... 5-41
PL 11.4 CCD PWB, Sensor............................................................................................ 5-42
PL 11.5 Carriage Cable/Motor........................................................................................ 5-43
PL 11.6 Full/Half Rate Carriage ..................................................................................... 5-44
12. Tray Module - 2T
PL 12.1 Tray, Feeder Assembly-2Tray .......................................................................... 5-45
PL 12.2 Tray 3/4 Assembly-2Tray.................................................................................. 5-46
PL 12.3 Tray 3/4 Feeder-2Tray...................................................................................... 5-47
PL 12.4 Left Cover-2Tray............................................................................................... 5-48
PL 12.5 Takeaway Roll-2Tray........................................................................................ 5-49
PL 12.6 Electrical-2Tray................................................................................................. 5-50
PL 12.7 Cover-2Tray...................................................................................................... 5-51
13. Tray Module - TT
PL 13.1 Tray 3/4 Assembly-Tandem Tray...................................................................... 5-52
PL 13.2 Tray 3 Assembly-Tandem Tray......................................................................... 5-53
PL 13.3 Tray 4 Assembly-Tandem Tray......................................................................... 5-54
PL 13.4 Paper Feed (1/2)-Tandem Tray ........................................................................ 5-55
PL 13.5 Paper Feed (2/2)-Tandem Tray ........................................................................ 5-56
PL 13.6 Tray 3/4 Feeder-Tandem Tray.......................................................................... 5-57
PL 13.7 Left Cover Assembly-Tandem Tray .................................................................. 5-58
PL 13.8 Electrical-Tandem Tray..................................................................................... 5-59
PL 13.9 Cover-Tandem Tray.......................................................................................... 5-60
14. Mobile Stand
PL 14.1 Mobile Stand..................................................................................................... 5-61
15. DADF
PL 15.1 DADF Accessory............................................................................................... 5-62
PL 15.2 DADF Component, Cover................................................................................. 5-63
PL 15.3 DADF Base Cover Component......................................................................... 5-64
PL 15.4 DADF Feeder Component ................................................................................ 5-65
PL 15.5 Top Cover Component...................................................................................... 5-66
PL 15.6 Takeaway Pinch Roll, Nudger Motor, Nudger/Feed Roll .................................. 5-67
PL 15.7 DADF Feeder-Chute......................................................................................... 5-68
PL 15.8 DADF Feeder-Roll ............................................................................................ 5-69
PL 15.9 Motor Unit ......................................................................................................... 5-70
PL 15.10 DADF Document Tray..................................................................................... 5-71