Page 116 FT-950 OPERATING MANUAL
TUNING GROUP
084 TUN DIALSTP
Function: Setting of the Main Tuning Dial knob’s and the
[
CLAR/VFO-B
]
knob’s tuning speed on the SSB, CW,
and AM modes.
Available Values: 1/5/10 Hz
Default Setting: 10 Hz
085 TUN CW FINE
Function: Enabling/disabling of the “Fine” tuning speed
in the CW mode.
Available Values: EnA/diS (ENABLE/DISABLE)
Default Setting: diS (DISABLE)
EnA (ENABLE): Tuning in 1 Hz steps on the CW mode.
diS (DISABLE): Tuning according to the steps deter-
mined via menu item “
084 TUN084 TUN
084 TUN084 TUN
084 TUN
DIALSTPDIALSTP
DIALSTPDIALSTP
DIALSTP”.
086 TUN MHz SEL
Function: Selects the tuning steps for the
[
CLAR/VFO-
B
]
knob when the
[
MHz
]
button is pressed.
Available Values: 1/0.1 MHz
Default Setting: 1 MHz
087 TUN AM STEP
Function: Selects the tuning steps for the microphone’s
[
UP
]
/
[
DWN
]
keys in the AM mode.
Available Values: 2.5/5/9/10/12.5 kHz
Default Setting: 5 kHz
088 TUN FM STEP
Function: Selects the tuning steps for the microphone’s
[
UP
]
/
[
DWN
]
keys in the FM mode.
Available Values: 5/6.25/10/12.5/20/25 kHz
Default Setting: 5 kHz
089 TUN FM DIAL
Function: Setting of the Main Tuning Dial knob’s and the
[
CLAR/VFO-B
]
knob’s tuning speed in the FM mode.
Available Values: 10/100 Hz
Default Setting: 100 Hz
090 TUN MY BAND
Function: Programs a band to be skipped while selecting
bands using the
[
CLAR/VFO-B
]
knob.
To program the band to be skipped, rotate the
[
CLAR/
VFO-B
]
knob to recall the band to be skipped while se-
lecting bands via the
[
CLAR/VFO-B
]
knob, then press
the
[
ENT
]
button to change this setting to “ON” (a “
dd
dd
d”
notation will replace the “
EE
EE
E” notation). Repeat the same
procedure to cancel the setting (skipped “Off”: “
dd
dd
d” nota-
tion appears).
TX AUDIO GROUP
091 TAUD EQ1 FRQ
Function: Selects the center frequency of the lower range
for the parametric microphone equalizer.
Available Values: OFF/100 ~ 700 Hz (100 Hz/step)
Default Setting: OFF
OFF: The equalizer gain and Q-factor are set to fac-
tory defaults (flat).
100 ~ 700: Center frequencies of 100 Hz ~ 700 Hz.
You may adjust the equalizer gain and Q-factor at this se-
lected audio frequency via menu items “
092 TAUD EQ1092 TAUD EQ1
092 TAUD EQ1092 TAUD EQ1
092 TAUD EQ1
LVLLVL
LVLLVL
LVL” and “
093 TAUD EQ1 BW093 TAUD EQ1 BW
093 TAUD EQ1 BW093 TAUD EQ1 BW
093 TAUD EQ1 BW”.
092 TAUD EQ1 LVL
Function: Adjusts the equalizer gain of the low range of
the parametric microphone equalizer.
Available Values: –20 ~ +10
Default Setting: +5
093 TAUD EQ1 BW
Function: Adjusts the Q-factor of the low range of the
parametric microphone equalizer.
Available Values: 1 ~ 10
Default Setting: 10
094 TAUD EQ2 FRQ
Function: Selects the center frequency of the middle range
for the parametric microphone equalizer.
Available Values: OFF/700 ~ 1500 Hz (100 Hz/step)
Default Setting: OFF
OFF: The equalizer gain and Q-factor are set to fac-
tory defaults (flat).
700 ~ 1500: Center frequencies of 700 Hz ~ 1500 Hz.
You may adjust the equalizer gain and Q-factor at this se-
lected audio frequency via menu items “
095 TAUD EQ2095 TAUD EQ2
095 TAUD EQ2095 TAUD EQ2
095 TAUD EQ2
LVLLVL
LVLLVL
LVL” and “
096 TAUD EQ2 BW096 TAUD EQ2 BW
096 TAUD EQ2 BW096 TAUD EQ2 BW
096 TAUD EQ2 BW”.
095 TAUD EQ2 LVL
Function: Adjusts the equalizer gain of the middle range
of the parametric microphone equalizer.
Available Values: –20 ~ +10
Default Setting: +5
096 TAUD EQ2 BW
Function: Adjusts the Q-factor of the middle range of the
parametric microphone equalizer.
Available Values: 1 ~ 10
Default Setting: 10
MENU MODE
To Next Page
Loading...
Need help?
General
