Home
Beckhoff
Touch terminals
EL2904
Beckhoff EL2904 User Manual
4
of 1
of 1 rating
54 pages
Give review
Manual
Specs
To Next Page
To Next Page
To Previous Page
To Previous Page
Loading...
Operation
EL2904
30
Version: 3.2.2
5.2.3.5
Signal cables
Permitted cable length
Fig.10: Permitted cable length
When connecting a single actuator via its own continuous cabling (or via a sheathed cable), the maximum
permitted cable length is 100 m.
The use of contact points, connectors or additional actuators in the cabling reduces the maximum
propagation.
Cable routing
Fig.11: Cable routing
29
31
Table of Contents
Table of contents
3
1 Notes on the documentation
5
1.1 Disclaimer
5
1.1.1 Trademarks
5
1.1.2 Patents
5
1.1.3 Limitation of liability
6
1.1.4 Copyright
6
1.2 Version numbers of the documentation
7
1.3 Staff qualification
8
1.4 Safety and instruction
9
1.5 Beckhoff Support and Service
10
2 For your safety
11
2.1 Duty of care
11
2.2 Safety image signs
12
2.3 General safety instructions
13
2.3.1 Before operation
13
2.3.2 During operation
13
2.3.3 After operation
13
3 System description
14
3.1 The Beckhoff Bus Terminal system
14
3.1.1 Bus Coupler
15
3.1.2 Bus Terminals
16
3.1.3 E-bus
16
3.1.4 Power contacts
16
3.2 TwinSAFE
16
3.2.1 The I/O construction kit is extended safely
16
3.2.2 Safety concept
17
3.2.3 EL1904, EL2904 - Bus Terminals with 4 fail-safe inputs or outputs
18
3.2.4 EL6900 - TwinSAFE logic terminal
18
3.2.5 The fail-safe principle (Fail Stop)
18
4 Product description
19
4.1 EL2904 – TwinSAFE terminal with 4 digital fail-safe outputs
19
4.2 Intended use
20
4.3 Technical data
22
4.4 Target failure measures
23
4.5 Dimensions
24
4.6 Block diagram of the EL2904
25
5 Operation
26
5.1 Environmental conditions
26
5.2 Installation
26
5.2.1 Safety instructions
26
5.2.2 Transport / storage
26
5.2.3 Electrical installation
26
5.2.3.1 Connections within a Bus Terminal block
26
5.2.3.2 Overvoltage protection
28
5.2.3.3 Wiring
28
5.2.3.4 EL2904 pin assignment
29
5.2.3.5 Signal cables
30
5.2.4 Mechanical installation
31
5.2.4.1 Control cabinet / terminal box
32
5.2.4.2 Installation position and minimum distances
32
5.2.4.3 Example configuration for temperature measurement
33
5.2.5 TwinSAFE reaction times
34
5.2.6 Tested EL2904 devices
35
5.3 Operation in potentially explosive atmospheres (ATEX)
36
5.3.1 Special conditions
36
5.3.2 Identification
36
5.3.3 Date code and serial number
37
5.3.4 Further ATEX documentation
37
5.4 Configuration of the terminal in TwinCAT
37
5.4.1 Inserting a Bus Coupler
37
5.4.2 Inserting a Bus Terminal
37
5.4.3 Inserting an EL2904
37
5.4.4 Address settings on TwinSAFE terminals with 1023 possible addresses
39
5.4.5 Entering a TwinSAFE address and parameters in the System Manager
40
5.5 Diagnostics
42
5.5.1 Diagnostic LEDs
42
5.5.2 Diagnostic objects
43
5.5.3 Possible causes of diagnostic messages
44
6 Lifetime
46
7 Maintenance and cleaning
47
7.1 Disassembly
47
8 Decommissioning
49
8.1 Disposal
49
8.1.1 Returning to the vendor
49
9 Appendix
50
9.1 Volatility
50
9.2 Focus of certificates
51
List of illustrations
52
4
Based on 1 rating
Ask a question
Give review
Questions and Answers:
Need help?
Do you have a question about the Beckhoff EL2904 and is the answer not in the manual?
Ask a question
Beckhoff EL2904 Specifications
General
Brand
Beckhoff
Model
EL2904
Category
Touch terminals
Language
English
Related product manuals
Beckhoff EL2809
160 pages
Beckhoff EL2124
168 pages
Beckhoff EL28 Series
160 pages
Beckhoff EL7031
255 pages
Beckhoff EL6731
188 pages
Beckhoff EL6910
105 pages
Beckhoff EL1904
57 pages
Beckhoff EL10 Series
106 pages
Beckhoff EL34 Series
295 pages
Beckhoff EL7041-1000
255 pages
Beckhoff EL72 1 Series
197 pages
Beckhoff EL72 1-901 Series
263 pages
To Next PageTo Next PageTo Previous PageTo Previous Page
Loading...
Need help?
General
