Bestway Lay-Z-Spa 54129 User Manual

12
Alarms
Solutions
Causes Reasons
The water flow sensors work
without pressing the filter or heat
button.
1. The water flow sensor flags didn’t fall back into the
correct position
2. The water flow sensors are broken
1. Unplug the plug gently, strike the side of the pump but not violently, and plug it
back in
2. Contact your local Bestway After Sales service point to get instructions
After starting or during the
functions of filtering or/and
heating, the water flow sensors
do not detect water flow.
1. You forgot to remove the 2 stopper caps from
inside the pool
2. Filter cartridges are dirty
3. Activate the filter or heat system and put your hand
in front of the outlet pipe inside the pool to check if
you can feel water flowing out
a. If no water flows out the water pump is broken
b. Water flows out but the alarm appears, the
water flow sensors are broken
1. Remove the 2 stopper caps before heating, refer to Assembly section in the
User’s Manual
2. Remove the filter set from inside the pool and push the filter or heat button. If no
alarm appears, clean or change the filter cartridges install the filter set inside the
pool.
3. Contact your local Bestway After Sales service point to get instructions
The manual reset thermal
cut-out has problem.
The manual reset thermal cut-out trips off
1. Unplug the pump and push the reset button, then plug the pump back in.
2. In case the alarm still remains, check the RESET BUTTON section in manual.
3. Contact your local Bestway After Sales service point to get instructions.
The pump’s thermometer
connections have issues.
1. The pump’s thermometer connectors don’t work
properly
2. The pump’s thermometer is broken
Contact your local Bestway After Sales service point to get instructions
The pump’s thermometer reads
the water temperature below
4°C (40°F).
1. The water temperature is lower than 4°C (40°F)
2. If the water temperature is higher than 7°C
(44.6°F), the pump’s thermometer is broken
1. The spa is not designed to operate with water temperatures lower than 4ºC
(40°F). Unplug the pump and only re-start the pump when the water temperature
reaches 6°C (43°F)
2. Contact your local Bestway After Sales service point to get instructions
The pump’s thermometer reads
the water temperature over
50°C (122°F).
1. The water temperature is over 50°C (122°F)
2. If the water temperature is lower than 45°C
(113°F), the pump’s thermometer is broken
1. The spa is not designed to operate with water temperatures greater than 40°C
(104°F). Unplug the pump and only re-start the pump when the water
temperature reaches 38°C (100°F) or lower.
IMPORTANT: Before you re-start the pump, push the pump’s
reset button
2. Contact your local Bestway After Sales service point to get instructions
MAINTENANCE
NOTE: Your spa will require additional air to be added from time to time. Changes in temperature from day to night will change the pressure in the spa and
may cause a certain amount of deflation. Please follow the Assembly instructions and drain the spa before inflating to the accurate pressure needed.
CAUTION: YOU MUST ENSURE THE PUMP IS UNPLUGGED BEFORE BEGINNING SPA MAINTENANCE TO AVOID RISK OF INJURY OR DEATH.
Filter Cartridge Maintenance
NOTE: To ensure your spa water stays clean, check and clean your filter cartridges every day follow the steps below.
P6653
Filter Set
58323
Filter Cartridge
NOTE: We recommend changing your filter cartridges every week or, if the filter cartridges remain soiled and discolored, they should be replaced.
Water Maintenance
Keeping your SPA water clean and chemically balanced is necessary. Simply cleaning the filter cartridge is not enough for proper maintenance,
we recommend you use pool chemicals to maintain water chemistry and chlorine or bromine tablets (do not use granules) with the chemical floater.
As a guide, the water should be changed about every 3 days. This is only a guide; water quality is influenced by frequency of use, persons
using the spa and general maintenance.
Note: We recommend you take a shower before using your Lay-Z-Spa, as cosmetic products, lotions, and other residues on
the skin can quickly degrade water quality.
To use the chemical floater, please follow the below instruction.
Using chemical tablets (not included):
-
l
o
i
n
5
s
e
c
.
Using chemical liquid (not included):
C
o
n
-
l
o
i
n
5
-
l
o
i
n
5
s
e
c
.
NOTE: Remove the chemical floater from spa when the spa is in use.
IMPORTANT: After performing chemical maintenance and before using the spa, use a test kit (not included) to test the water chemistry.
We recommend maintaining your water as table below.
pH Total Alkalinity Free Chlorine
7.4-7.6 80-120 ppm 2-4 ppm
NOTE: Damage resulting from chemical imbalance is not covered by the warranty. Pool chemicals are potentially toxic and should be handled with care.
There are serious health risks from chemical vapors and the incorrect labeling and storage of chemical containers. Please consult your local pool supply
retailer for more information about chemical maintenance. Pay close attention to the chemical manufacturer's instructions. Spa damage resulting from
misuse of chemicals and mismanagement of spa water is not covered by the warranty.
S-S-004675/21x28.5cm/54112AU 54123AU 54129AU 54148AU 54154AU 54156AU 澳规SPA说明书/JS-YF-2016-B-05546/英
S-S-004675

Bestway Lay-Z-Spa 54129 Specifications

General

Brand	Bestway
Model	Lay-Z-Spa 54129
Category	Hot Tub
Language	English