Bestway Lay-Z-Spa 54129 User Manual

Problems
Pump does not operate
Pump does not
heat properly
Lay-Z-Massage System
does not work
Pump adapters are not
level with the spa
adapters
Spa pool leakage
Water is not clean
Probable Causes
- Spa is torn or punctured
- Air valve is loose
Solutions
- Check power source
- Contact your local Bestway Aftersales Service Center for instructions
- Elevate the pump with wood or another type of insulated material to
bring the pump's adapters level with the spa's adapters
- Power failure
- Power circuits broken
- Air Pump is overheating
- The Lay-Z-Spa Massage
stops automatically
- Air pump is broken
One characteristic of PVC
is that it changes shape,
which is normal
- Insufficient filtering time
- Dirty Filter Cartridge
- Improper water maintenance
- Unplug the pump and wait two hours until the pump has cooled. Insert
the plug and press the Lay-Z-Massage System Button
- Press the Lay-Z-Massage System Button to reactivate
- Contact your local Bestway Aftersales Service Center for instructions
- Increase filtration time
- Clean/replace the Filter Cartridge (refer to Filter Cartridge Cleaning and
Replacement section)
- Refer to the chemical manufacturer’s instructions
PRCD test failed
Something wrong with
the SPA
Contact your local Bestway Aftersales Service Center
and return the SPA.
Control panel not
working
The control panel has an auto-lock,
which is activated after 5 minutes of
inactivity. The LED display has one
icon: If the lock icon is highlighted,
the control panel is locked.
- Control panel is not activated.
What kind of chemicals
should be used for water
maintenance?
Please consult your local chemical supplier for information about
chemical maintenance.
Pay close attention to the chemical manufacturer’s instructions.
Water leaks from the
adapters between the
pump and spa
Insert the stopper caps on to the spa’s ports to prevent water from escaping and disconnect the pump. Check and
make sure the seals are placed correctly inside the pump adapters. If the seals are missing or not installed
correctly, please contact your local Bestway Aftersales Service Center for instructions. If the seals are correctly in
place, reconnect the pump to the spa and hand-tighten the adapters.
- Use provided repair patch
- Using soapy water, cover the air-valve to check if air is leaking, if so,
use the provided wrench to fasten the air-valve following these steps:
1. Deflate the SPA.
2. With one hand, hold the backside of the air valve from the inner side
of the spa wall and turn the wrench clockwise.
- Temperature set too low
- Dirty Filter Cartridge
- The thermal cut-out cut off
- Spa is not covered
- Heating element failed or
fuse cutout
- Set to a higher temperature refer tosection pump operation
- Clean/replace the filter cartridge referto section filter cartridge
cleaning and replacement
- Unplug the pump, and put the plug in a dry, cool place. Only restart the
pump when the water temperature reaches 35°C (95°F) or lower
- Attach the cover.
- Contact your local Bestway After Sales service point to get instructions
- To unlock the control panel, press the button for 3 seconds.
If the control panel will not unlock, restart the pump – unplug and
plug in the pump.
- Press the on/off button for 2 seconds. If the problem persists,
please contact your local Bestway Aftersales Service Center
for instructions.
TROUBLESHOOTING Bestway strives to provide the most trouble-free spas on the market.
If you experience any problems whatsoever, do not hesitate to contact Bestway or your
authorized dealer. Here are some helpful tips to help you to diagnose and rectify some common
sources of trouble.
14
S-S-004675/21x28.5cm/54112AU 54123AU 54129AU 54148AU 54154AU 54156AU 澳规SPA说明书/JS-YF-2016-B-05546/英
S-S-004675

Bestway Lay-Z-Spa 54129 Specifications

General

Brand	Bestway
Model	Lay-Z-Spa 54129
Category	Hot Tub
Language	English