Bosch DIVAR 3000 User Manual

Installation
Notice!
Use proper surge suppression on cables that are routed outdoors, or close to large inductive
loads or electrical mains supply cables.
!
Caution!
Installation should only be performed by qualified service personnel in accordance with the
National Electrical Code (NEC 800 CEC Section 60) or applicable local codes.
To get the unit operational, perform the following quick install steps:
1. Carefully unpack the recorder from its shipping packaging – see Unpacking.
2. Make all required hardware connections – see ‘Make Connections’.
3. Power up the system – see Powering Up.
4. Log in – see Login.
5. Correctly configure your system software with the Startup wizard (this appears the first
time the unit is started) – see Startup Wizard.
After completing this initial setup, the system is ready to run and will show a live view of the
camera image(s). If required, you can alter the settings later using the menus and/or factory
defaults, or you can run the Startup wizard again.
Unpacking
This equipment should be unpacked and handled with care. If an item appears to have been
damaged in shipment, notify the shipper immediately.
Verify that all parts are included. If any items are missing, notify your Bosch Security Systems
Sales or Customer Service Representative.
The original packaging is the safest container in which to transport the unit and can be used if
returning the unit for service.
Package contents
Qty Component
1 Recorder
1 Optical disc containing software licenses and user documentation
2 Power supply cables (120VAC US type; 230VAC Euro type)
1 External power supply adapter (only for DIVAR 2000/3000 network (non-PoE)
models and DIVAR 3000 hybrid models)
Terminal connector blocks
1 19” mounting set including brackets and screws (only on DIVAR 5000 models)
1 Hard disk mounting kit (including SATA cables, brackets and screws)
1 Optical USB mouse
1 IR remote Control with 2 AA (1.5 V) batteries
1 Ground screw
5
5.1
5.1.1
12 en | Installation
DIVAR 2000 / DIVAR 3000 / DIVAR
5000
2016.09 | v1.0 | AM18-Q0717 Operation Manual Bosch Security Systems

Bosch DIVAR 3000 Specifications

General

AC input voltage	100 - 240 V
AC input frequency	50 - 60 Hz
Power consumption (max)	20 W
Storage temperature (T-T)	0 - 93 °C
Operating temperature (T-T)	0 - 40 °C
Storage relative humidity (H-H)	0 - 95 %
Operating relative humidity (H-H)	-40 - 70 %
Sustainability certificates	RoHS
Certification	EMC, LVD, UL, cUL, CAN/CSA, BIS, RCM, ACMA EMC, CE, FCC
On/off switch	Yes
Product color	Black, Silver
Rack capacity	-
Bit rate	24000 Kbit/s
Display modes	Live view
Playback modes	Fast play, Forward, Frame by Frame, Reverse, Slow play
Input bandwidth	320 Mbit/s
Number of users	128 user(s)
Recording modes	Manual, Schedule, Stop
Output bandwidth	256 Mbit/s
Maximum resolution	3840 x 2160 pixels
Alarm input channels	16
Video input channels	16 channels
Alarm output channels	3
Supported resolutions	3840×2160, 1920×1080, 1280×1024, 1280×720, 1024×768, 970x576, 704x576, 352x576, 352x288, 176x144, 960x480, 704x480, 352x480, 352x240, 176x120
Video recording modes	720p, 1080p
Video formats supported	H.264, H.265, M-JPEG
RS-232 ports	1
Audio RCA inputs	4
Networking standards	IEEE 802.3
USB 2.0 ports quantity	USB 2.0 ports have a data transmission speed of 480 Mbps, and are backwards compatible with USB 1.1 ports. You can connect all kinds of peripheral devices to them.
Ethernet LAN data rates	10, 100, 1000 Mbit/s
Ethernet LAN (RJ-45) ports	2
Supported network protocols	HTTP, HTTPS, TCP/IP, IPv4/IPv6, UPnP, RTSP, UDP, SMTP, NTP, DHCP, DNS/DDNS, IP Filter, PPPoE, FTP
Copper ethernet cabling technology	10BASE-T, 100BASE-T, 1000BASE-T
Wi-Fi	No
HDD capacity	- GB
HDD interface	Serial ATA
Maximum storage capacity	6 TB
Mobile operating systems supported	Android, iOS

Weight and Dimensions

Depth	323 mm
Width	375 mm
Height	53 mm
Weight	4130 g