Bosch Indego M+ 700 User Manual

32 | English
Problem Possible Cause Corrective Measure
After watering, wait as long as possible until you start the
mower.
Mower unintentionally
cuts flowers, etc. or
runs over certain
obstacles
Objects/obstacles below 5cm not marked
out
Mark obstacle using perimeter wire leaving 30cm from
object or remove objects/obstacles.
Mower does not ap-
pear to cut logically
LogiCut system depends on the garden
conditions. Mower does not necessarily
have to continue in the next uncut area.
Further information can be found on the Installation
Guide.
If behaviour re-occurs often, remap garden.
Mower does not always go in a straight line
when travelling between areas
No corrective action needed.
Mower frequently does not find right posi-
tion or turns on the spot
Change wire ID.
Wire crossed while marking an object Follow instructions in the Installation Guide.
Mower runs in random paths in an addi-
tional lawn without docking station.
Normal behaviour. The LogiCut system only works in
areas with docking station.
Perimeter wire keeps
being cut
Wire is not taut between pegs
Distance between pegs is more than 75cm
Make wire taut and ensure distance between pegs is
maximum 75 cm. Follow instructions in the Installation
Guide. Use the wire connectors to repair the cut.
Mower leaves ragged
finish/poor quality of
cut
The mower does not mow often enough Mow more frequently for a good result (e.g. by means of
more/longer slots in schedule).
Cutting blades blunt
Reverse or replace cutting blades (see figure J).
Possible clogging Always turn isolator switch off first, then check under-
neath the mower. Clear out as necessary (always wear
protective gloves).
Perimeter wire not
detected
No power at the docking station Check if the docking station is powered up (LED is on).
Perimeter wire damaged/cut Check perimeter wire for damage.
Wrong installation (e.g. not enough dis-
tance between wires)
Follow instructions in the Installation Guide.
Perimeter wire close to a source of interfer-
ence
Remove any excess (e.g. coiled up) perimeter wire
around the docking station. Change perimeter wire ID in
the menu.
Height-of-cut button
stuck
Possible clogging Always turn isolator switch off first, then check under-
neath the mower. Clear out as necessary (always wear
protective gloves).
After-sales Service and Application
Service
www.bosch-garden.com
In all correspondence and spare parts orders, please always
include the 10-digit article number given on the type plate of
the mower.
It is possible, that the software version of your mower is re-
quired (see „Menu > Settings > Info“).
If the mower is requested to be sent to the service centre,
the mower and docking station must always be sent to-
gether. Do not remove the battery.
Before sending in, remove any personalised top cover that
may have been fitted and any accessory cover.
Great Britain
Robert Bosch Ltd. (B.S.C.)
P.O. Box 98
Broadwater Park
North Orbital Road
Denham Uxbridge
UB 9 5HJ
At www.bosch-pt.co.uk you can order spare parts or arrange
the collection of a product in need of servicing or repair.
Tel. Service: (0344) 7360109
E-Mail: boschservicecentre@bosch.com
Ireland
Origo Ltd.
Unit 23 Magna Drive
Magna Business Park
City West
F 016 L81 041 | (15.04.2020) Bosch Power Tools

Bosch Indego M+ 700 Specifications

General

Type	Robotic lawn mower
Motor type	Brushless
Cutting width	190 mm
Product color	Black, Green
Cutting system	Rotary blades
Maximum lawn area	700 m²
Maximum cutting height	50 mm
Minimum cutting height	30 mm
Suitable for slope up to	27 %
Number of height positions	3
Cutting clearance adjustment	Yes
Battery type	Built-in battery
Power source	Battery
Charging time	1 h
Battery voltage	18 V
Battery life (max)	75 min

Weight and Dimensions

Weight	7100 g