Bosch Solution 880 CC408 User Manual

CC408 | Quick Reference Guide | 3. Programming Parameters EN | 14
Bosch Security Systems | 6/04 | 4998152468B
3.10.14 System Status – Access Denied
(Code Retry)
Location
356 to 358
Location Default
Code retry limit
(0 = unlimited)
356 6
Tens digit 357 7
Units digit 358 12
3.10.15 System Status Reporting Options
Location
359
0 No Codepad Alarm Reports allowed
1 Report to Receiver 1
2 Report to Receiver 2
4 Report to both Receiver 1 and Receiver 2
8 Report to Receiver 2 only if Receiver 1 fails
3.10.16 Test Report Time (Automatic)
Location
360 to 366
Location Default
Hour of day (tens digit) 360 0
Hour of day (units digit) 361 0
Minute of day (tens digit) 362 0
Minute of day (units digit) 363 0
Test Report (tens digit) 364 7
Test Report (units digit) 365 1
Repeat interval in days 366 0
3.10.17 Test Reporting Dialler Options
Location
367
0 No Codepad Alarm Reports allowed
1 Report to Receiver 1
2 Report to Receiver 2
4 Report to both Receiver 1 and Receiver 2
8 Report to Receiver 2 only if Receiver 1 fails
3.11 Outputs Programming
3.11.1 Outputs
Location
368 to 397
Location Default
Output 1 (Default = Horn speaker)
Event Code 368 1
Event Code 369 14
Polarity 370 0
Time Base 371 0
Time Base Multiplier 372 0
Time Base Multiplier 373 0
Output 2 (Default = Fire alarm with verification)
Event Code 374 2
Event Code 375 7
Polarity 376 10
Time Base 377 2
Time Base Multiplier 378 1
Time Base Multiplier 379 5
3.11.1 continued
Location
368 to 397
Location Default
Strobe Output
(Default = Strobe – reset after 8 hours)
Event Code 380 2
Event Code 381 0
Polarity 382 6
Time Base 383 4
Time Base Multiplier 384 0
Time Base Multiplier 385 8
Relay Output (Default = Sirens running)
Event Code 386 1
Event Code 387 15
Polarity 388 1
Time Base 389 0
Time Base Multiplier 390 0
Time Base Multiplier 391 0
Codepad Buzzer
(Default = Entry/exit warning plus day alarm)
Event Code 392 0
Event Code 393 13
Polarity 394 2
Time Base 395 1
Time Base Multiplier 396 0
Time Base Multiplier 397 1
3.11.2 Event Codes
Event
Code
Description
0 0 EDMSAT – satellite siren (Output 1 only)
0 1 System armed
0 2 System disarmed
0 3 Armed in STAY Mode
0 4 Armed in AWAY Mode
0 5 Pre-arming alert
0 6 Exit warning (all zones sealed) and entry
warning
0 7 Exit warning
0 8 Exit warning finished
0 9 Kiss-off after end of exit time
0 10 Reserved
0 11 Entry warning
0 12 Entry warning and day alarm resetting
0 13 Exit warning and entry warning and day
alarm resetting
0 14 Day alarm resetting
0 15 Day alarm latching
1 0 Day alarm enabled
1 1 Telephone line fail
1 2 Kiss-off received
1 3 Fuse fail
1 4 AC fail
1 5 Low battery
1 6 Horn speaker fail
1 7 Sensor watch alarm
1 8 Codepad medical alarm
1 9 Codepad fire alarm

Bosch Solution 880 CC408 Specifications

General

Brand	Bosch
Model	Solution 880 CC408
Category	Control Panel
Language	English