CC408 | Quick Reference Guide | 3. Programming Parameters EN | 17
Bosch Security Systems | 6/04 | 4998152468B
3.14.2 System Options 2
Location
425
Default
0
1 Codepad panic to be silent
2 Codepad fire to be silent
4 Codepad medical to be silent
8 Access denied (code retries) to be silent
3.14.3 System Options 3
Location
426
1 AC fail after 1 hour (Disabled = after 2 minutes)
2 Ignore AC fail
4 Pulse count handover allowed
8 Handover delay to be sequential
3.14.4 System Options 4
Location
427
Default
0
1 Panel to power up disarmed (if power reset)
2 Arm/disarm tracking on power up
4 Internal crystal to keep time
8 Radio keyswitch interface, night arm station, or
RE005 installed
3.15 Consumer Options Programming
3.15.1 Consumer Options 1
Location
428
Default
0
1 Test reports only when armed
2 Test report after siren reset
4 Auto arm in STAY Mode 1
8 STAY indicator to display day alarm status
3.15.2 Consumer Options 2
Location
429
1 Codepad display extinguish after 60 seconds
2 Single button arming allowed
(AWAY/STAY Modes 1 and 2)
4 Single button disarming allowed
(STAY Modes 1 and 2)
8 Alarm memory reset on disarm
3.15.3 Consumer Options 3
Location
430
1 Codepad fault beeps allowed
2 Use digit 3 for codepad duress alarm (instead of
digit 9)
4 Alarms activate sirens and strobe outputs in
STAY Modes 1 and 2
8 Reserved
3.16 Radio Input Options
Location
431
Default
0
1 Radio receiver (WE800)
2 Latching keyswitch input
3 Momentary keyswitch input
4 Reserved
3.17 Partioning
3.17.1 Partitioning Options 1
Location
432
Default
0
1 First to open/last to close reporting allowed
2 Area 1 codepad connected to data terminal
4 Request sirens from any area allowed
8 Master codepad to display AUX indicator when
on-line
3.17.2 Partitioning Options 2
Location
433
Default
0
1 Lock Area 1 to Receiver 1 and Lock Area 2 to
Receiver 2
2 User codes allowed to arm/disarm both areas at
same time ([code][0 #])
4 Reserved
8 Reserved
3.18 Zone Allocation Programming
3.18.1 Zone Allocations for Area 1
Location
434 to 441
Location Default
Zone 1 LED – Area 1 codepad 434 0
Zone 2 LED – Area 1 codepad 435 0
Zone 3 LED – Area 1 codepad 436 0
Zone 4 LED – Area 1 codepad 437 0
Zone 5 LED – Area 1 codepad 438 0
Zone 6 LED – Area 1 codepad 439 0
Zone 7 LED – Area 1 codepad 440 0
Zone 8 LED – Area 1 codepad 441 0
3.18.2 Zone Allocations for Area 2
Location
442 to 449
Location Default
Zone 1 LED – Area 2 codepad 442 0
Zone 2 LED – Area 2 codepad 443 0
Zone 3 LED – Area 2 codepad 444 0
Zone 4 LED – Area 2 codepad 445 0
Zone 5 LED – Area 2 codepad 446 0
Zone 6 LED – Area 2 codepad 447 0
Zone 7 LED – Area 2 codepad 448 0
Zone 8 LED – Area 2 codepad 449 0
To Next Page
Loading...
Need help?
General
