To Next Page

To Previous Page

QUICK SPECIFICATIONS

COOLING & ELECTRIC HEAT

MODEL NUMBER

Cooling

Capacity

(BTUH)

EER

Electrical

Heating Ca-

pacity

(BTUH)

Reverse

Cycle Heat

(BTUH)

COP

Voltage

Range

Indoor CFM COOLING Approx.

Ship

Weight lb.

Low Med High AMPS WATTS

5 2 M E --- U 0 7 --- --- --- 3 --- ---

Determined

by your power

cord selection.

See chart be-

low.

--- ---

187 --- 253

--- --- --- --- --- ---

5 2 M E --- U 0 9 --- --- --- 3 8800 / 9000 11.4 / 11.4 --- --- 265 290 330 3.9 / 3.7 770 / 790 125

5 2 M E --- U 1 2 --- --- --- 3 12,000 / 12,100 11.4 / 11.5 --- --- 280 300 320 5/ 4.7 1060 / 1070 140

5 2 M E --- U 1 5 --- --- --- 3 --- --- --- --- --- --- --- --- --- ---

5 2 M E --- U 0 7 --- --- --- 4 --- --- --- ---

239---292

--- --- --- --- --- ---

5 2 M E --- U 0 9 --- --- --- 4 9,100 11.7 --- --- 265 300 320 3.3 790 125

5 2 M E --- U 1 2 --- --- --- 4 12,100 11.5 --- --- 280 310 345 4.35 1050 140

5 2 M E --- U 1 5 --- --- --- 4 --- --- --- --- --- --- --- --- --- ---

HEAT PUMPS

Model No.

Cooling

Capacity

(BTUH)

EER

Electrical

Heating Capa-

city (BTUH)

Reverse Cycle

Heat (BTUH)

COP

Voltage

Range

Indoor CFM COOLING

Approx. Ship

Weight lb.

Low Med High AMPS WATTS

5 2 M Q --- U 0 7 --- --- --- 3 --- ---

Determined by

your power

cord selection.

See chart be-

low.

--- --- --- --- --- --- --- --- ---

5 2 M Q --- U 0 9 --- --- --- 3 8,800 / 9,000 10.5 / 10.5 8,300 / 8,350 3.4 / 3.3 187 ---253 270 320 350 4.1 / 3.9 840 860 125

5 2 M Q --- U 1 2 --- --- --- 3 12,000 / 12,000 11.1 / 11.1 10,700 / 10,900 3.4 / 3.3 187---253 280 320 350 5.1 / 4.8 1080 1090 140

5 2 M Q --- U 1 5 --- --- --- 3 --- --- --- --- --- --- --- --- --- --- ---

5 2 M Q --- U 0 7 --- --- --- 4 --- --- --- --- --- --- --- --- --- --- ---

5 2 M Q --- U 0 9 --- --- --- 4 9,000 10.9 8,400 3.5 239---292 275 285 300 3.2 825 125

5 2 M Q --- U 1 2 --- --- --- 4 11,400 10.8 10,600 3 239---292 220 250 290 4.2 1,050 140

5 2 M Q --- U 1 5 --- --- --- 4 15,000 --- --- --- --- --- --- --- --- --- ---

POWER CORD SELECTION:

52M PTACs are not individually equipped with a power cord, so one must be ordered separately based on the voltage and amperage of your electrical circuit. If the

unit i s t o be plugged into a recept acle, then a l ine cord connecti on ki t needs to be sel ect ed. If i t will be permanentl y connect ed, a hardwire connection must be used.

Model No. Voltage Receptacle Type

Heating

(BTUH)

Heater (Kw)

Input Power

(Watts)

Current

(Amps)

Branch Circuit

Full Amps

PWRCORD--- 230V --- 15A

208/230V

15 amp /250V 7,800 / 6,400 2.5 2,393 / 1,985 10.4 / 9.5 15

PWRCORD--- 230V --- 20A 20 AMP / 250V 11,600 / 9,700 3.4 3,493 / 2,935 11.52 / 14.1 20

PWRCORD--- 230V --- 30A 30 AMP / 250V 17,000 / 13,600 5.0 5,170 / 4,147 22.5 / 20.0 30

PWRCORD--- 265V --- 15A

265V

15 AMP / 277V 7,800 2.5 2,396 9.2 15

PWRCORD--- 265V --- 20A 20 AMP / 277V 11,600 3.4 3,496 13.3 20

PWRCORD--- 265V --- 20A 30 AMP / 277V 17,000 5.0 5,170 19.6 30

NOTE: In compliance with UL, and the National Electrical Code, 265V units installed iwth a power cord require the u se use of a 265V electrical subbase.

Always look for these symbols, the air conditioning

industr

seals of certified

erformance, efficienc

and ca

acit

52M