Operation Guide 5551
E-19
Note
• After you specify a city code, the watch will use UTC* offsets in the World Time
Mode to calculate the current time for other time zones based on the current time in
your Home City.
* Coordinated Universal Time, the world-wide scientific standard of timekeeping.
The reference point for UTC is Greenwich, England.
E-18
Configuring Home City Settings
There are two Home City settings: actually selecting the Home City, and selecting
either standard time or daylight saving time (DST).
To configure Home City settings
1. In the Timekeeping Mode, hold down
A
until ADJ
appears.
• This indicates the city code setting mode.
2. Press
D
(East) and
B
(West) to select the city code
you want to use as your Home City.
• For details about city codes, see the “City Code
Table” at the back of this manual.
3. After the setting is the way you want, press
A
to return
to the Timekeeping Mode.
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
City Code
E-17
To swap your Home City and World Time City
In the Timekeeping Mode, hold down
D
for about three seconds.
This swaps your Home City and World Time City.
Example: To swap the Home City (TYO) and World Time City (NYC)
Current Home City (TYO) time New Home City (NYC) time
Current Home City (TYO) information New Home City (NYC) information
Current World Time City
(NYC) time
New World Time City
(TYO) time
Hold down
D
New Home City
E-16
Timekeeping
Use the Timekeeping Mode to set and view the current time and date.
• Each press of
A
cycles the Home City information as
shown below.
Day of week,
Seconds
Month, Day,
Seconds
Hour : Minutes,
Seconds
PM indicator
A
A
A
Home City information
Home Time :
hour and minutes
World Time :
hour and minutes
B
E-15
2. Holding down
B
again as you press
C
will cause the hands to return to their
normal positions (normal timekeeping).
Note
• Watch button functions are the same regardless of whether the hands are move out
of the way or at their normal positions.
• Changing to another mode will cause the hands to move back to their normal
positions.
• The hands also will move back to their normal positions automatically if no operation
is performed for about one hour.
E-14
Moving the Hands Out of the Way for Better Viewing
You can use the procedure below to temporarily move the hour and minute hands out
of the way to better view what is on the display.
• This operation can be performed in any mode. In the case of a setting mode
(information flashing on the display), the hands will move out of the way
automatically, even if you do not perform the operation below.
1. While holding down
B
, press
C
.
• This will cause the hour and minute hands to move to
a location where they do not block your view of the
World Time and/or digital display.
Flashes while the hands
are moved out of the way.
E-13
Graphic Area
• The graphic area indicates the seconds count in the Timekeeping Mode (page E-16),
World Time Mode (page E-25), Stopwatch Mode (page E-28), and Timer Mode (page E-31).
E-12
General Functions (All Modes)
The functions and operations described in this section can be used in all of the modes.
•
Auto Return Features
The watch will automatically return to the Timekeeping Mode if you do not perform any
operation for a certain amount of time, as described below.
Mode Approximate Elapsed Time
Alarm
2 to 3 minutes
Time or other setting mode
(information flashing on the display)
•
Scrolling
The
B
and
D
buttons are used on the setting mode to scroll through data on the
display. In most cases, holding down these buttons during a scroll operation scrolls
through the data at high speed.
E-11
Stopwatch Mode Countdown Timer Mode Alarm Mode
CC
C
E-10
Selecting a Mode
• Press
C
to cycle between the modes as shown below.
• To return to the Timekeeping Mode from any other mode, hold down
C
for about
two seconds.
• In any mode (except a setting mode), press
B
to illuminate the display.
Home Time : hour and minutes
World Time : hour and minutes
Timekeeping Mode World Time Mode
CC
To Next Page
Loading...
Need help?
General
