Operation Guide 5551
E-29
To perform an elapsed time operation
D D D D A
Start Stop Resume Stop Reset
To pause at a split time
D
A A D A
Start Split
(
SPL
displayed)
Split release Stop Reset
To measure two finishes
D
A D A A
Start Split
(
SPL
displayed)
First runner finishes.
Display time of first
runner.
Stop
Second runner
finishes.
Split release
Display time of
second runner.
Reset
E-28
Using the Stopwatch
The stopwatch measures elapsed time, split times, and two finishes.
To enter the Stopwatch Mode
Use
C
to select the Stopwatch Mode as shown on page E-11.
Minutes
Seconds
1/100 second
E-27
To specify standard time or daylight saving time (DST) for a city
In the World Time Mode, hold down
A
for about two
seconds.
• This toggles between Daylight Saving Time (
DST
indicator displayed) and standard time (
DST
indicator
not displayed).
• Note that you cannot switch between standard time/
daylight saving time (DST) while UTC is selected as the
World Time City.
• The standard time/daylight saving time (DST) setting
affects only the currently displayed city. Other cities are
not affected.
DST indicator
E-26
To enter the World Time Mode
Use
C
to select the World Time Mode as shown on page E-10.
• The display changes as shown below.
Mode name
A
World Time City city code
and name will scroll.
World Time City
city code
• Press
A
to display the city code and name of the currently selected city.
To view the time in another time zone
Pressing
D
changes the city code setting.
• Each press of
D
advances to the next city code.
• To change the city code to UTC, press
B
and
D
at the same time.
E-25
Checking the Current Time in a Different Time Zone
You can view the current time in one of 31 time zones (48 cities) around the globe.
The city that is currently selected in the World Time Mode is called the “World Time
City”.
There are two World Time City settings: actually selecting the World Time City, and
selecting either standard time or daylight saving time (DST).
World Time City
Home Time :
hour and minutes
World Time : hour and minutes
PM indicator
E-24
Note
• Resetting the seconds to 00 while the current count is in the range of 30 to 59
causes the minutes to be increased by 1.
• While the 12-hour format is selected for timekeeping, a
P
(PM) indicator will appear
for times from noon to 11:59 p.m. No indicator appears for times from midnight to
11:59 a.m. With 24-hour format, time is displayed from 0:00 to 23:59, without any
P
(PM) indicator.
• The watch’s built-in full automatic calendar makes allowances for different month
lengths and leap years. Once you set the date, there should be no reason to
change it except after you have the watch’s battery replaced.
• The day of the week changes automatically when the date changes.
E-23
3. When the timekeeping setting you want to change is flashing, use
D
and/or
B
to
change it as described below.
Screen To do this: Do this:
Toggle between 12-hour (
12H
) and 24-hour
(
24H
) timekeeping
Press
D
.
Reset the seconds to
00
Press
D
.
Change the hour or minute Use
D
(+) and
B
(–).
Change the year Use
D
(+) and
B
(–).
Change the month or day Use
D
(+) and
B
(–).
4. Press
A
to exit the setting mode.
E-22
2. Press
C
to move the flashing in the sequence shown below to select the other
settings.
City Code
(page E-18)
DST
(page E-20)
Hour
Minutes
YearMonthDay
Button Operation Tone On/Off
(page E-45)
Illumination Duration
(page E-38)
12/24-Hour Format
C
C
C
C
CCC
Seconds
C
C
C
C
E-21
Configuring Current Time and Date Settings
You can use the procedure below to adjust the Timekeeping Mode time and date
settings if they are off.
Changing the digital Home City data should cause the analog time setting to change
accordingly. If the analog time does not indicate the digital time, check the home
positions of the hands and make adjustments if necessary (page E-43).
To change the current time and date settings
1. In the Timekeeping Mode, hold down
A
until ADJ
appears.
• This indicates the city code setting mode.
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
E-20
To change the Daylight Saving Time (summer time) setting
1. In the Timekeeping Mode, hold down
A
until ADJ
appears.
• This indicates the city code setting mode.
2. Press
C
to display the DST setting mode.
3. Press
D
to toggle between Daylight Saving Time (ON)
and Standard Time (OFF).
• Note that you cannot switch between daylight saving
time and standard time while UTC is selected as your
Home City.
4. After the setting is the way you want, press
A
to return
to the Timekeeping Mode.
• The
DST
indicator appears to indicate that Daylight
Saving Time is turned on.
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
DST indicator
To Next Page
Loading...
Need help?
General
