Tape Operations
Tape
repeat play
The tape repeat continuously plays the current
track. This function continues automatically until
it
is
canceled.
1.
Press the [RPT] button. "RPT" lights in the
display and the
cu
rrent track is repeated.
2.
To
cancel the repeat play, press the [RPT]
button again. "RPT" goes off from the display
and normal play resumes.
Blank tape skip
The blank tape skip allows you to skip blank sec-
tions of tape that are over 12 seconds long.
1.
Press and hold the [RPT] button for more than
1 seconds. The blank skip feature will be set
and
"BLS"
will light
on
the display. When there
is
an
unrecorded section of more than
12
sec-
onds,
"BLS"
will light
on
the display and the
section will be skipped.
2.
To
cancel the blank skip feature, press and
hold the [RPT] button again for more than 1
second.
"BLS"
on
the display will disappear.
Notes:
The
APe,
intra tape scan, tape
repeat
and
bfank
skip may
not
work properly with tapes
of
the follow-
ing qualities:
•
Tapes
on which the recording fevel is too
low.
•
Tapes
on which there is much noise between se-
lections.
•
Tapes
on which there are
fang
pauses
in
the middle
of
selections.
•
Tapes
on which there are less than 4 seconds
of
blank space between selections.
Operations
Common
to
Each
Mode
Setting the clock
1.
Press and hold the [TITLE] button for 1 sec-
ond or longer to switch to the adjustment se-
lection display.
2.
Press the
[~/II]
button.
3.
Press the [
....
] or
[~~]
button
to
select the
hour or the minute.
4.
Turning the [VOLUME] knob either clockwise
or counterclockwise to set the correct time.
The clock
is
displayed
in
12-hour format.
5.
Press the
[~/II]
button to store the time into
memory.
6.
Press the [TITLE] button
to
return
to
the pre-
vious mode.
Note:
•
You
cannot
set
the clock when it is displayed with
only the ignition
on.
ff
you drain
or
remove the car's
battery
or
take out this unit, the clock is reset. While
setting the clock,
if
another button
or
operation is
selected, the clock set mode is canceled.
Setting the sensitivity
of
the
spec~
trum analyzer
The
factory default setting
is
"MID".
1.
Press and hold the [TITLE] button for 1 sec-
ond or longer
to
switch
to
the adjustment se-
lection display.
2.
Press the [
....
] or
[~]
button
to
select "ANA
SENS",
3.
Turning the [VOLUME] knob either clockwise
or counterclockwise
to
set the sensitivity of
the spectrum analyzer.
You can
choose
one
of "LOW", "MID" or
"HIGH" for the sensitivity of the spectrum ana-
lyzer.
4.
Press the [TITLE] button
to
return to the pre-
vious mode.
16
ADB340MP/ADB341 MP
Setting the speed
of
the spectrum
analyzer display
The
factory default setting
is
"LOW".
1.
Press and hold the [TITLE] button for 1 sec-
ond or longer to switch to the adjustment se-
lection display.
2.
Press the [
....
] or
[~~]
button
to
select "ANA
SPO".
3.
Turning the [VOLUME] knob either clockwise
or counterclockwise to set the speed of the
spectrum analyzer display.
You can
choose
one
of
"LOW",
"MID" or
"HIGH" for the speed of the spectrum ana-
lyzer display.
To Next Page
Loading...
Need help?
General
