Other Handy
Functions
Setting the
clock
1 Press and hold ADJ button
~
for 1 second or
longer to switch to the adjustment selection
display
2 Press Right button
~
or Left button
l1ID
to se-
lect
"CLOCK"
3 Press ENT button [g]
4 Press Right button
~
or Left button
l1ID
to se-
lect the hour or the minute
5 Press Up button
I11l
or press Down button
11m
to set the correct time
*The clock is displayed
in
12-hour format
6
Press
ENT
button
[g]
to
store
the
time
into
memory
7
Press
ADJ
button
~
to
return
to
the
previous
mode
Note:
•
You
cannot
set
the
clock
when
it
is
displayed
with
only
the ignition on
If
you
drain
or
remove the car's
battery
or
take
out
this unit, the clock is reset While
setting
the clock,
if
another
button
or
operation is
selected, the
clock
set
mode
is
canceled
Switching
the
spectrum
analyzer
display
patterns
You
can select one out of 4 patterns or set it to
off
*The factory default setting is "PATTERN 1"
Each time you press SPE-ANA button
@J,
the
spectrum analyzer display pattern changes
in
the
following order
PATTERN 1 PATTERN 2 PATTERN 3 ...
PATTERN 4 PATTERN 5 PATTERN 6
...
PATTERN 7 PATTERN 8 PATTERN 9 ...
OFF ... PATTERN 1
Note:
The spectrum
analyzer
display is unavailable dur-
ing these operations below;
•
Seek
tuning
and
auto
store in radio
mode
• Mute
or
pause
• When "NO
DISC"
or
an
error
message
appears
in the display.
Setting
the
sensitivity
of
the spec-
trum
analyzer
*The factory default setting is "MID"
16
AOX5655z
1 Press and hold ADJ button
~
for 1 second or
longer to switch to the adjustment selection
display
2 Press Right button
~
or Left button
l1ID
to se-
lect
"ANA
SENS"
3 Press Up button
I11l
or Down button
11m
to set
the sensitivity of the spectrum analyzer
You
can
choose
one
of
"LOW", "MID"
or
"HIGH" for the sensitivity of the spectrum ana-
lyzer
4 Press ADJ button
~
to return to the previous
mode
Setting
the
speed
of
the
spectrum
analyzer
display
*The factory default setting is "HIGH"
1 Press and hold ADJ button
~
for 1 second or
longer to switch to the adjustment selection
display
2 Press Right button
~
or Left button
l1ID
to se-
lect
"ANA
SPD"
3 Press Up button
I11l
or Down button
11m
to set
the speed of the spectrum analyzer display
You
can
choose
one
of
"LOW", "MID"
or
"HIGH" for the speed of the spectrum analyzer
display
4 Press ADJ button
~
to return to the previous
mode
Entering
titles
Titles up to 10 characters long can be stored
in
memory and displayed for radio or TV stations
and CDs
The
numbers
of titles
that
can be
entered for each mode are as follows
Mode
Number
of
titles
Radio mode 30 titles
CD mode 100 titles
TV mode
15 titles
CD
changer
mode
Number
of
titles
CDC655z connected 60 titles
CDC655Tz connected 100 titles
CDC1255z connected 50 titles
1 Press
FU
NC
button
[l]
to select the mode
you
want to enter a title (radio,
CD,
CD changer or
TV)
*Titles cannot be entered for MDs with this unit
2 Select and playaCD or a CD
in
the CD changer,
or tune to
an
appropriate TV or radio station
3 Press DISP button
[1J
and display the title
To Next Page
Loading...
Need help?
General
