D-Link DGS-108 User Manual

D-Link DGS-108 Unmanaged Gigabit Ethernet Switch
14
half duplex – A system that allows packets to be transmitted and received, but not at the same time.
Contrast with full duplex.
IP address – Internet Protocol address. A unique identifier for a device attached to a network using TCP/IP.
The address is written as four octets separated with full-stops (periods), and is made up of a network section,
an optional subnet section and a host section.
IPX – Internetwork Packet Exchange. A protocol allowing communication in a NetWare network.
LAN – Local Area Network. A network of connected computing resources (such as PCs, printers, servers)
covering a relatively small geographic area (usually not larger than a floor or building). Characterized by
high data rates and low error rates.
latency – The delay between the time a device receives a packet and the time the packet is forwarded out of
the destination port.
line speed
– See baud rate.
main port – The port in a resilient link that carries data traffic in normal operating conditions.
MDI – Medium Dependent Interface. An Ethernet port connection where the transmitter of one device is
connected to the receiver of another device.
MDI-X – Medium Dependent Interface Cross-over. An Ethernet port connection where the internal transmit
and receive lines are crossed.
MIB – Management Information Base. Stores a device’s management characteristics and parameters. MIBs
are used by the Simple Network Management Protocol (SNMP) to contain attributes of their managed
systems. The Switch contains its own internal MIB.
multicast – Single packets copied to a specific subset of network addresses. These addresses are specified in
the destination-address field of the packet.
protocol – A set of rules for communication between devices on a network. The rules dictate format, timing,
sequencing, and error control.
resilient link – A pair of ports that can be configured so that one will take over data transmission should the
other fail. See also main port and standby port.
RJ-45 – Standard 8-wire connectors for IEEE 802.3 10BASE-T networks.
RMON
– Remote Monitoring. Subset of SNMP MIB II, which allows monitoring and management
capabilities by addressing up to ten different groups of information.
RPS – Redundant Power System. A device that provides a backup source of power when connected to the
Switch.
server farm – A cluster of servers in a centralized location serving a large user population.
SLIP – Serial Line Internet Protocol. A protocol that allows IP to run over a serial line connection.
SNMP
– Simple Network Management Protocol. A protocol originally designed to be used in managing
TCP/IP internets. SNMP is presently implemented on a wide range of computers and networking equipment
and may be used to manage many aspects of network and end station operation.
Spanning Tree Protocol
– (STP) A bridge-based system for providing fault tolerance on networks. STP
works by allowing you to implement parallel paths for network traffic, and to ensure that redundant paths
are disabled when the main paths are operational and enabled if the main paths fail.
stack – A group of network devices that are integrated to form a single logical device.
standby port – The port in a resilient link that will take over data transmission if the main port in the link
fails.
switch – A device that filters, forwards, and floods packets based on the packet’s destination address. The
Switch learns the addresses associated with each switch port and builds tables based on this information to
be used for the switching decision.
TCP/IP – A layered set of communications protocols providing Telnet terminal emulation, FTP file transfer,
and other services for communication among a wide range of computer equipment.
Telnet – A TCP/IP application protocol that provides virtual terminal service, letting a user log in to another
computer system and access a host as if the user were connected directly to the host.
TFTP – Trivial File Transfer Protocol. Allows you to transfer files (such as software upgrades) from a
remote device using your switch’s local management capabilities.

D-Link DGS-108 Specifications

General

MAC address table	8000 entries
Jumbo frames support	Yes
Packet buffer memory	0.128 MB
Maximum data transfer rate	1 Gbit/s
Supported data transfer rates	10/100/1000 Mbps
Dimensions (WxDxH)	162 x 102 x 28 mm
Connectivity technology	Wired
10G support	-
Networking standards	IEEE 802.1p, IEEE 802.3, IEEE 802.3ab, IEEE 802.3az, IEEE 802.3u, IEEE 802.3x
Copper ethernet cabling technology	1000BASE-T, 100BASE-TX, 10BASE-T
Switch type	Unmanaged
Switch layer	L2
Power connector	DC-in jack
Installed SFP modules quantity	0
Basic switching RJ-45 Ethernet ports type	Gigabit Ethernet (10/100/1000)
Basic switching RJ-45 Ethernet ports quantity	8
Certification	FCC Class B, ICES-003 Class B, CE Class B, C-Tick Class B, VCCI Class B, cUL, CB, RoHS
Product color	Black
Rack mounting	No
LED indicators	Link, Power, Y
Housing material	Metal
Input current	1 A
Input voltage	5 V
Power consumption (typical)	4.5 W
Mean time between failures (MTBF)	2053751 h
Heat dissipation	9.548 BTU/h
Storage temperature (T-T)	10 - 70 °C
Operating temperature (T-T)	0 - 50 °C
Storage relative humidity (H-H)	5 - 90 %
Operating relative humidity (H-H)	10 - 90 %
Harmonized System (HS) code	85176990

Weight and Dimensions

Weight	440 g