17
6. The machine delivers the chosen quantity of hot water,
then delivery stops automatically. To stop delivery manu-
ally, press " " .
Preparation stops automatically.
Please note!
• If "Energy Saving" mode is active, you may have to wait a
few seconds before the hot water is delivered.
• The quantity of water in the cup can be customised (see
sections “16. Customising the beverages” and “17. Memo-
rising your personal prole”).
• Delivery can be stopped at any moment by pressing "
";
• As soon as delivery has ended, to increase the quantity of
water in the cup, just press " EXTRA". When the required
quantity is reached, press " ".
12. DELIVERING HOT WATER
Important! Danger of burns.
Do not leave the appliance unattended while hot water is being
delivered.
1. Make sure the hot water/steam spout (C6) is attached cor-
rectly to the hot water/steam connection nozzle (A9);
2. Place a container under the spout (as close as possible to
avoid splashes);
3. " HOT WATER". The corresponding image appears on
the display (B), together with a progress bar which lls
gradually as preparation proceeds;
4. The machine delivers about 250 ml of hot water, then de-
livery stops automatically. To interrupt hot water delivery
manually, press " " .
Please note!
• If "Energy Saving" mode is active, you may have to wait a
few seconds before the hot water is delivered.
• Preparation of hot water can be customised (see sections
“16. Customising the beverages” and “17. Memorising your
personal prole”).
13. STEAM DELIVERY
Important! Danger of burns.
Do not leave the appliance unattended while steam is being
delivered.
1. Make sure the hot water/steam spout (C6) is attached cor-
rectly to the hot water/steam connection nozzle (A9);
2. Fill a container with the liquid to be heated or frothed and
immerse the hot water/steam spout in the liquid;
3. Press " STEAM". The corresponding image appears
on the display (B), together with a progress bar which lls
gradually as preparation proceeds and after a few seconds,
steam to heat the liquid is delivered from the hot water/
steam spout;
4. When the required temperature or level of froth is reached,
interrupt steam delivery by pressing " ";
Important!
Always stop steam delivery before extracting the container con-
taining the liquid to avoid burns from splashes.
Please note!
If "Energy saving" is active, you may have to wait a few seconds
before steam is delivered.
13.1 Tips for using steam to froth milk
• When choosing the size of the container, bear in mind that
the liquid doubles or triples in volume.
• For a richer denser froth, use skimmed or partially skimmed
milk at refrigerator temperature (about 5°C).
• For a creamier froth, rotate the container with slow move-
ments in an upward direction.
• To avoid milk with poor froth or large bubbles, always clean
the spout (C6) as described in the following section.
13.2 Clean the hot water/steam spout after use
Always clean the hot water/steam spout (C6) after use to avoid
the build-up of milk residues and prevent it from clogging.
5. Place a container under the hot water/steam spout and de-
liver a little water (see section “12. Delivering hot water”).
Stop delivery of hot water by pressing " ".
6. Wait a few minutes for the hot water/steam spout to cool
down, then extract (g. 18) by pressing the release button
(C7). Hold the spout with one hand and with the other, turn
the cappuccino maker and pull it downwards (g. 26).
7. Also remove the steam connection nozzle by pulling it
downwards (g. 27).
8. Check the hole in the connection nozzle is not blocked. If
necessary, clean using a toothpick.
9. Wash all parts of the spout thoroughly with a sponge and
warm water.
10. Insert the connection nozzle, then the cappuccino maker
on the nozzle by pushing it upwards and turning it clock-
wise until it is attached.
To Next Page
Loading...
Need help?
General
