8
en
Operation
Using the remote control unit
TURNING THE APPLIANCE ON
Before plugging the appliance check the caps on the back
of the unit are correctly inserted and screwed on the
drainage hose 10.
Plug into the electrical receptacle. Two lines appear on the
display indicating that the appliance is in stand-by. Press the
ON/OFF button (A). When turned on, the air conditioner starts
operating in the same mode as when it was turned o. Press
the MODE button (B) until the light corresponding to the desired
mode lights up:
Light(O): air-conditioning mode
Light(P): dehumidifying mode
Light(N): fan mode
AIR CONDITIONING MODE
Ideal for hot muggy weather when you need to cool and
dehumidify the room.
Thedisplayshowstheinnertemperature:thelight(S) turns on.
Tomodifythe settemperature,pushthe(E) or (F) button to
reachthedesiredtemperature.The(T) light turns on and the
(S) light turns o.
Tochangefrom°Fto°Corviceversa,pressforfewsecondsboth
button E and F.
After 15 seconds, the inner temperature is shown on the
display.
The(S) light turns on.
Youcanadjustthetemperatureonlyinairconditioningmode.
ThenselectthefanspeedbypressingtheFAN button (C) until
the light corresponding to the required fan speed lights up:
MAX: the air conditioner operates at maximum to
achieve the target temperature as rapidly as
possible
MED: reduces noise levels while maintaining a
comfortable temperature
MIN: for silent operation
The most suitable indoor temperature for the room during
the summer varies from 75°F to 81°F (24 to 27°C). You are
recommended, however, not to set a temperature much below the
outdoor temperature.
FAN MODE
AdjustfanspeedbypressingtheFAN button (C) as described
for the air-conditioning mode.
Remember that the higher the speed, the more air is ltered.
If you select “MIN” speed, less air is ltered but the appliance
is also less noisy.
DEHUMIDIFYING MODE
Ideal for reducing the humidity in a room without lowering or
raising the temperature (spring or autumn, damp rooms, rainy
spells, etc). When the dehumidifying mode is selected, the
light (P) comes on. At the same time, the “MIN” fan speed light
(M) comes on. In this mode, other speeds cannot be selected.
In dehumidifying mode, the appliance MUSTbeset-upinthe
same way as for air conditioning, with the air exhaust hose 12
attached.
PROGRAMMING THE TIMER
Thetimercanbeusedtodelayappliancestartuporshutdown.
Thisavoidswastingelectricitybyoptimisingoperatingperiods.
How to programme delayed start up
• Plugtheapplianceintoanelectricalreceptacleandpress
the ON/OFF button (A), then select the required operating
mode and other settings (temperature, fan speed, etc).
• PresstheON/OFFbutton(A) again to place the appliance
in standby mode.
• Pressthetimerbutton(D).Thetimerlight“H” ashes.
• Usethe+(E) or - (F) buttons to set the number of hours
delaybeforetheappliancecomeson.Thetimeincreasesor
decreases in steps of one hour.
Theindicatorlight(H) ashes until the appliance starts up.
Youcansettheappliancetocomeonwithadelayofupto12
hours.Tocancelthetimerprogramme,pressthetimerbutton
(D)again.Light(H) stops ashing.
How to programme delayed shut down
• Delayedshutdowncanbeprogrammedinanyoperating
mode (air conditioning/fan/dehumidifying).
• Pressthetimerbutton(D).Thetimerlight“H” ashes.
• Usethe+(E) or - (F) buttons to set the number of hours
delay before the appliance goes o.
Thetimeincreasesordecreasesinstepsofonehour.
The light (H) ashes until the appliance turns o as
programmed. At the set time, the air conditioner shuts down
andremainsinstandby.Tocancelthetimerprogramme,press
the timer button (D)again.Light(H) stops ashing.
USING THE REMOTE CONTROL
• Point the remote control at the receiver on the air
conditioner.Theremotecontrolmustbenomorethan
16,4ft (5 meters) away
from the appliance
(without obstacles
between the remote
MAX 16 ft
MAX 5 meters