Delta DJ-15 User Manual

SAFETY RULES
Woodworking can l>e dangerous it sate and proper operating procedures are not followed. As with all machinery, there are certain
hazards involved with the operation ot the product. Using the machine with respect and caution will considerably lessen the
possibiiiy ot personal injury I lowever. If normal safety precautions are overlooked or ignored, personal miury to the operator may
result. Safely equipment such as guards, push sticks hold-downs, fealherboards. goggles, dust masks and hearing protection
can reduce your potential lot injury Rut oven the best guard won't make up tor poor judgment, carelessness or inattention Always
use common sense and exorcise caution in the workshop. If a procedure feels dangerous, don't try it Figure out an alternative
procedure that feels safer MLMLMBER: Your personal safety is your responsibility.
This machine was designed for certain applications only. Della Machinery strongly recommends lhal this machine not be modified
cind/ui used loi any application other than that (or which it was designed. It you have any questions relative to a particular
application, DO NOT use the machine until you have first contacted Delta to determine if it can or should be performed on the
product.
DELTA INTERNATIONAL MACHINERY CORP.
MANAGER OF TECHNICAL SERVICES
246 ALPHA DRIVE
PITTSBURGH. PENNSYLVANIA 15238
ON CANADA: 644 IMPERIAL ROAD GUELPH, ONTARIO N1H 6M7»
WARNING: FAILURE TO FOLLOW THESE RULES
MAY RESULT IN SERIOUS PERSONAL INJURY
1. FOR YOUR OWN SAFETY. READ INSTRUCTION
MANUAL BEFORE OPERATING THE TOOL Learn the
tool's application and limitations as well as the specific hazards
peculiar toil.
2 . KEEP GUARDS IN PLACE and in working order.
3 Al WAYS WEAR FYE PROTECTION
4. GROUND ALL TOOLS. II tool is equipped with three-
prong plug, it should be plugged into a three-hole electrical
receptacle If an adapter is used to accommodate a two-prong
receptacle the adapter lug must be attached to a known
ground. Never renxjvc the third prong.
5. REMOVE ADJUSTING KFYS ANn WRFNCHES Form
habit of checking to see lhal keys and adjusting wrenches are
removed Irom tool before turning it ‘ on. 1 '
6 . KEEP WORK AREA CLEAN. Clullored areas and
benches invite accidents.
7 DON'T USE IN DANGEROUS ENVIRONMENT Don!
use power tools in damp nr wet locations, nr expose them to
rain. Keep work area well-lighted,
ft. KEEP CHILDREN AND VISITORS AWAY All children
and visitors should be kept a safe distance from work area.
9 MAKE WORKSHOP CHILDPROOF - wilh padlocks,
master switches. or by removing starter keys
1 0 DON'T FORCE TOOL. 11 will do the job better and be safer
at the rate for which it was designed.
11 . USE RIGHT TOOL Don't force tool or attachment to do
a job for which it was not designed.
12 WEAR PROPER APPAREL No loose clothing, gloves,
neckties, rings, bracelets, or other jewelry to gel caught in
moving parts. Nonclip footwear io recommended. Wear
protective hair covenng to contain long hair.
13 ALWAYS USE SAFETY GLASSES Wear salely glasses
(must comply with ANSI ZQ7 1 ). Lveryday eyeglasses only
have impact resistant lenses: they are not salely glasses Also
use face or dust mask il culling operation is dusty.
14 SECURE WORK Uccclampc ora vice to hold work when
practical. It's safer than using your hand and Irees both hands
to operate tod.
15. DON’T OVERREACH Keep proper footing and balance
at all lirnos.
16 MAINTAIN TOOLS IN TOP CONDITION Keep tools
sharp and clean for best and safest performance Follow
instructions for lubricating and changing accessories.
l/. DISCONNECT TOOLS betore servicing and when
changing accessories such as blades, bits, cutters etc
18. USE RECOMMENDED ACCESSORIES The use of
accessories and attachments not recommended by Delta
may cause hazards or risk of injury lo persons
19 REDUCE THE RISK OF UNINTENTIONAL START¬
ING. Make sure switch is in OFF" position before plugging in
power cord.
20 NEVER STAND ON TOOL Serious injury could occur if
the tool is tipped or il the culling tool is accidentally contacted.
21. CHECK DAMAGED PARTS Before further use of the
tool, a guard or other port that 13 damaged should be carefully
checked lo ensure lhal il will operate properly and perform its
intended function check for alignment ol moving parts,
binding ol moving parts, breakage of parts, mounting, and any
other conditions that may affecl ils operation A guard or other
part that is damaged should be properly repaired or replaced.
22 . DIRECTION OF FEED Feed work into a blade or culltor
against the direction of rotation of the blade or cutter only.
23 NEVER LEAVETOOLRUNNINGUNATTENDED TURN
POWER OFF. Don't leave fool until it comes to a complete
stop.
24. DRUGS, ALCOHOL. MEDICATION Do not operate tool
while under Hu; influence of drugs, alcohol or any medication.
25. MAKE SURE TOOL IS DISCONNECTED FROM POWER
SUPPLY while motor is being mounted, connected or
reconnected.
26. WARNING: The dust generated by certain woods and
wood products can bo injurious to your health. Always operate
machinery in well ventilated areas and provide for proper dust
removal. Use wood dust collection systems whenever possible.
3

Delta DJ-15 Specifications

General

Brand	Delta
Model	DJ-15
Category	Power Tool
Language	English