Denon RCD-N7 User Manual

31
Getting Started Connections
Basic Operations Advanced OperationsAdvanced Operations TroubleshootingExplanation termsInformation Specifi cations Index
ENGLISH
Canceling the party mode
1
Press [MENU].
Turns on the Menu settings mode and the Menu appears on
the display. (vpage25 “Menu map”)
2
Use ui to select “Network” – “Party Mode” –
“Stop Party”, then press [ENTER], <1/3 ENTER >
or p.
“Exit Party Mode?” is displayed on the menu screen.
3
Use ui to select “Yes”, then press [ENTER], <1/3
ENTER > or p
“Attendees P.Off?” is displayed.
4
Use ui to select “Yes” or “No”, then press
[ENTER], <1/3 ENTER > or p.
Yes
: The power of the attendees is turned off and the party
mode is canceled.
No
: The party mode is canceled without turning off the power
of the attendees.
n Participating in the party mode as an attendee
• When the organizer starts the party mode, up to four attendees
are selected automatically. No operation is required.
• When a device becomes an attendee,
Party Mode Attendee
appears
on the display. The input source automatically switches to
“Internet Radio” and the same network audio as on the organizer
is played.
• If there are fewer than four attendees, a device can join the
party mode after it has started. To participate in the party mode,
perform the operation described below.
1
Press [MENU].
Turns on the Menu settings mode and the Menu appears on
the display. (vpage25 “Menu map”)
2
Use ui to select “Network” – “Party Mode” –
“Start Party”, then press [ENTER], <1/3 ENTER >
or p.
• An error message is displayed when you are not connected to a
network.
Canceling the party mode
1
Press [MENU].
Turns on the Menu settings mode and the Menu appears on
the display. (vpage25 “Menu map”)
2
Use ui to select “Network” – “Party Mode” –
“Stop Party”, then press [ENTER], <1/3 ENTER >
or p.
“Exit Party Mode?” is displayed on the menu screen.
3
Use ui to select “Yes”, then press [ENTER], <1/3
ENTER > or p
In this case, the other devices remain in the party mode.
“Last.fm”, “Napster” and “USB” are not available in the Party Mode.
There can only be one organizer in the network. To form a new party
mode, fi rst cancel the current party mode.
n Setting the Party Start Level
Make settings for volume level when the party mode is started.
1
Press [MENU].
Turns on the Menu settings mode and the Menu appears on
the display. (vpage25 “Menu map”)
2
Use ui to select “Network” – “Party Mode” –
“Party Start Level”, then press [ENTER], <1/3
ENTER > or p.
• Last : The same volume as set before the party mode was started.
• 00 : Always use the muting on condition when the party mode is
started.
• 01 – 60dB : Start party mode with your preferred volume.
This can be set when “Party Mode Function“ is set to “ON“.
Setting the network [Network]
Party Mode Function
The same network audio (Internet radio, music server or iPod DIRECT)
can be played on multiple DENON products equipped with the Party
Mode function and connected in a network.
The party mode consists of one organizer and up to four attendees.
When one unit starts the party mode as the organizer, up to four
devices on which the party mode function is activated automatically
participate in the party as attendees. “Party Mode Function” must be
set to “ON” ahead of time in order to use the party mode function.
n Setting the Party Mode Function
1
Press [MENU].
Turns on the Menu settings mode and the Menu appears on
the display. (vpage25 “Menu map”)
2
Use ui to select “Network” – “Party Mode” –
“Party Mode Function”, then press [ENTER], <1/3
ENTER > or p.
“P-Mode Function” menu appears.
3
Use ui to select “On” or “Off” , then press
[ENTER], <1/3 ENTER > or p.
On
: Enable party mode function.
Off
: Disable party mode function.
n Starting the party mode as the organizer
1
Press [MENU].
Turns on the Menu settings mode and the Menu appears on
the display. (vpage25 “Menu map”)
2
Use ui to select “Network” – “Party Mode” –
“Start Party”, then press [ENTER], <1/3 ENTER >
or p.
• An error message is displayed when you are not connected to a
network.
• The input source automatically switches to “Internet Radio” and
the attendees are automatically selected.
3
Play the desired station.
1.RCDN7E2ENG5th0831.indd311.RCDN7E2ENG5th0831.indd31 2010/09/0115:10:032010/09/0115:10:03

Denon RCD-N7 Specifications

General

Frequency range	5 - 20000 Hz
RMS rated power	65 W
Pre-out channels	1 SW
Input sensitivity	200 mV
Pre-out connectivity	Yes
Audio output channels	2.0 channels
Signal-to-Noise Ratio (SNR)	100 dB
Total Harmonic Distortion (THD)	0.7 %
Dynamic power per channel (4 Ohm)	80 W
Power output per channel (20-20KHz@8 Ohm)	- W
Audio (L/R) in	2
Digital audio optical in	1
Headphone connectivity	3.5 mm
Connectivity technology	Wired & Wireless
Speakers connectivity type	Binding post
Audio formats supported	AAC, FLAC, MP3, WMA
Image formats supported	JPG
Video formats supported	AVI, WMV
AM band range	522 - 1611 kHz
FM band range	87.5 - 108 MHz
Supported radio bands	AM, FM
Preset stations quantity	99
Internet radio services supported	Last.fm, Napster
Optical drive type	CD player
Disc types supported	CD, CD-R, CD-RW
Display	OLED
Product color	Silver
Audio decoders	Not supported
Volume control	Rotary
Apple docking compatibility	iPhone, iPod
Number of products included	1 pc(s)
AC input voltage	230 V
AC input frequency	50 Hz
Power consumption (standby)	0.4 W

Weight and Dimensions

Depth	299 mm
Width	280 mm
Height	112 mm
Weight	4300 g