DeWalt DCN650 Original Instructions

7
ENGLISH
Mains Plug Replacement
(U.K.& Ireland Only)
If a new mains plug needs to be fitted:
• Safely dispose of the oldplug.
• Connect the brown lead to the live terminal in theplug.
• Connect the blue lead to the neutralterminal.

WARNING: No connection is to be made to the
earthterminal.
Follow the fitting instructions supplied with good quality plugs.
Recommended fuse: 3A.
Using an Extension Cable
An extension cord should not be used unless absolutely
necessary. Use an approved extension cable suitable for
the power input of your charger (see Technical Data). The
minimum conductor size is 1mm
2
; the maximum length
is30m.
When using a cable reel, always unwind the cablecompletely.
Important Safety Instructions for All Battery
Chargers
SAVE THESE INSTRUCTIONS: This manual contains important
safety and operating instructions for compatible battery
chargers (refer to TechnicalData).
• Before using charger, read all instructions and cautionary
markings on charger, battery pack, and product using
batterypack.

WARNING: Shock hazard. Do not allow any liquid to get
inside charger. Electric shock mayresult.

WARNING: We recommend the use of a residual current
device with a residual current rating of 30mA orless.

CAUTION: Burn hazard. To reduce the risk of injury,
charge only DeWALT rechargeable batteries. Other types of
batteries may burst causing personal injury anddamage.

CAUTION: Children should be supervised to ensure that
they do not play with theappliance.
NOTICE: Under certain conditions, with the charger
plugged into the power supply, the exposed charging
contacts inside the charger can be shorted by foreign
material. Foreign materials of a conductive nature such
as, but not limited to, steel wool, aluminum foil or any
buildup of metallic particles should be kept away from
charger cavities. Always unplug the charger from the
power supply when there is no battery pack in the cavity.
Unplug charger before attempting toclean.
• DO NOT attempt to charge the battery pack with any
chargers other than the ones in this manual. The charger
and battery pack are specifically designed to worktogether.
• These chargers are not intended for any uses other than
charging DeWALT rechargeable batteries. Any other uses
may result in risk of fire, electric shock orelectrocution.
• Do not expose charger to rain orsnow.
• Pull by plug rather than cord when disconnecting
charger. This will reduce risk ofdamage to electric plug
andcord.
Chargers
DeWALT chargers require no adjustment and are designed to be
as easy as possible tooperate.
Electrical Safety
The electric motor has been designed for one voltage only.
Always check that the battery pack voltage corresponds to the
voltage on the rating plate. Also make sure that the voltage of
your charger corresponds to that of yourmains.
i
Your DeWALT charger is double insulated in
accordance with EN60335; therefore no earth wire
isrequired.
If the supply cord is damaged, it must be replaced only by
DeWALT or an authorised serviceorganisation.
Residual Risks
In spite of the application of the relevant safety regulations
and the implementation of safety devices, certain residual risks
cannot be avoided. These are:
• Impairment ofhearing.
• Risk of personal injury due to flyingparticles.
• Risk of burns due to accessories becoming hot
duringoperation.
• Risk of personal injury due to prolongeduse.
SAVE THESE INSTRUCTIONS
the insulation of electric cables thereby causing electric shock
or firehazards.
• Always wear safetyglasses.
• Always wear earprotection.
• Only use fasteners of the type specified in themanual.
• Do not use any stands for mounting the tool to
asupport.
• Do not disassemble or block any parts of the fastener
driving tool such as the contacttrip.
• Prior to each operation check that the safety and triggering
mechanism is functioning properly and that all nuts and bolts
aretight.
• Do not use the tool as ahammer.
• Always check local workplaceregulations.
• Never point any operational fastener driving tool at
yourself or at any otherperson.
• While working, hold the tool in such a way that no
injuries can be caused to the head or to the body in
the event of a possible recoil due to a disruption in the
energy supply or hard areas within the workpiece.
• Never actuate the fastener driving tool into freespace.
• In the work area, carry the tool at the workplace using
only one handle, and never with the triggeractuated.
• Consider the conditions in the work area fasteners can
penetrate thin work pieces or slip off corners and edges
of the work piece, and thus put people atrisk.
• Do not drive fasteners close to the edge of the
workpiece.
• Do not drive fasteners on top of otherfasteners.

DeWalt DCN650 Specifications

General

Brand	DeWalt
Model	DCN650
Category	Nail Gun
Language	English