EINHELL GC-DP 1020 N User Manual

GB
- 15 -
3. Proper use
The equipment you have purchased is designed
to pump water with a maximum temperature of
35 °C. This equipment must never be used for
other liquids, especially not for engine fuels,
cleaning agents and other chemically-based
products!
The equipment can be used wherever you want to
move water, e.g. in the house, in the garden, and
for many other applications. It must not be used to
operate swimming pools!
If you want to use the equipment in bodies of wa-
ter with a natural, muddy bottom, place the equip-
ment in a slightly elevated position, e.g. on bricks.
The equipment is not designed for continuous
operation, e.g. as a circulating pump in a pond. In
this case the equipment’s anticipated life will be
greatly shortened because the equipment was
not designed for continuous loading.
The equipment is to be used only for its prescri-
bed purpose. Any other use is deemed to be a
case of misuse. The user / operator and not the
manufacturer will be liable for any damage or inju-
ries of any kind caused as a result of this.
Please note that our equipment has not been de-
signed for use in commercial, trade or industrial
applications. Our warranty will be voided if the
machine is used in commercial, trade or industrial
businesses or for equivalent purposes.
The water may be contaminated by escaping lub-
ricating oil/lubricant.
4. Technical data
Mains connection ........................... 230 V ~ 50 Hz
Power rating ............................................. 1000 W
Max. pumping rate .................................18000 l/h
Max. delivery head ......................................... 9 m
Max. submersion depth .................................. 5 m
Max. water temperature ............................... 35°C
Hose connection ..........approx. 47.8 mm (1½ “) IG
Max. size of foreign bodies: ....................Ø 20 mm
Switching point height: ON .....max. approx. 50 cm
Switching point height: OFF ......min. approx. 5 cm
Protection type. .............................................IPX8
5. Before starting the equipment
Before you connect the equipment to the mains
supply make sure that the data on the rating plate
are identical to the mains data.
5.1 Installation
The equipment can be installed either:
•
Stationary with a rigid pipe line
or
•
Stationary with a flexible hose line
Notice!
Before you use the pump, clarify any possible
special conditions which need to be fulfi lled for
the installation!
For example, additional safety measures may be
needed if damage to property could result from a
power failure, soiling or a defective gasket.
Examples of such safety measures:
Pumps running in parallel on a separately protec-
ted power circuit, moisture sensors for switching
off the pumps, and similar safety arrangements.
Be sure to consult a professional plumber if you
have any doubt.
The maximum pumping rate is possible only with
the largest possible line diameter; if smaller hoses
or pipes are connected, the pumping rate will be
reduced.
Connecting the discharge line
Matching connection elbows and hose connec-
tors for connecting the discharge line are included
among the items supplied. Use the connection
elbow which matches the hose diameter (see
Fig. 2).
Anl_GC_DP_1020_N_SPK9.indb 15Anl_GC_DP_1020_N_SPK9.indb 15 16.04.2020 09:13:4116.04.2020 09:13:41
Autogoods “130”
130.com.ua

EINHELL GC-DP 1020 N Specifications

General

AC input voltage	230 V
AC input frequency	50 Hz
Flow rate	18000 l/h
Motor power	- hp
Maximum delivery height	9 m
Depth of immersion (max)	5 m
Maximum operating pressure	- bar
Solid particles size (max)	20 mm
Maximum input water temperature	35 °C
Cable length	10 m
Suction port	1\
Connecting thread type	-
Proper use	What is the intended application of the product?
Product color	Red, Silver
Housing material	Stainless steel
Dimensions (WxDxH)	170 x 235 x 415 mm
Carrying handle(s)	Yes
Quantity	1

Weight and Dimensions

Depth	225 mm
Width	170 mm
Height	415 mm
Weight	7200 g
Package weight	7800 g