EINHELL TC-AG 125 User Manual

GB
- 18 -
the direction in which the tool rotates.
Take special care that the grinding/sanding
wheels are properly stored and transported.
Ensure that the grinding/sanding wheels are
never exposed to shock, jolts or sharp edges (for
example during transport or storage in a toolbox).
This could cause damage (such as cracks) to the
grinding/sanding wheels and place the user in
serious danger.
Warning!
6.6 Operating Modes
6.6.1 Rough grinding
 Caution: Use the safety device for san-
ding/grinding (included in items supplied).
For the best rough grinding results, hold the grin-
ding wheel at an angle of between 30° and 40° to
the workpiece surface and guide back and forth
over the workpiece in steady movements.
6.6.2 Cutting
 Caution: Use the safety device for abrasi-
ve cutting (available as accessory, see 8.4)
When you use the right-angle grinder for cutting
purposes, avoid tilting it in the cutting plane. The
cutting wheel must have a clean cutting edge.
A diamond cutting wheel is best used to cut hard
stone.
 It is prohibited to use the machine on as-
bestos materials!
 Never use a cutting wheel for rough grin-
ding.
7. Replacing the power cable
Danger!
If the power cable for this equipment is damaged,
it must be replaced by the manufacturer or its
after-sales service or similarly trained personnel
to avoid danger.
8. Cleaning, maintenance and
ordering of spare parts
Danger!
Always pull out the mains power plug before star-
ting any cleaning work.
8.1 Cleaning
•
Keep all safety devices, air vents and the
motor housing free of dirt and dust as far as
possible. Wipe the equipment with a clean
cloth or blow it with compressed air at low
pressure.
•
We recommend that you clean the device
immediately each time you have finished
using it.
•
Clean the equipment regularly with a moist
cloth and some soft soap. Do not use
cleaning agents or solvents; these could at-
tack the plastic parts of the equipment. Ensu-
re that no water can seep into the device. The
ingress of water into an electric tool increases
the risk of an electric shock.
8.2 Carbon brushes
In case of excessive sparking, have the carbon
brushes checked only by a qualifi ed electrician.
Danger! The carbon brushes should not be rep
laced by anyone but a qualifi ed electrician.
8.3 Maintenance
There are no parts inside the equipment which
require additional maintenance.
8.4 Ordering replacement parts:
Please quote the following data when ordering
replacement parts:
•
Type of machine
•
Article number of the machine
•
Identification number of the machine
•
Replacement part number of the part required
For our latest prices and information please go to
www.isc-gmbh.info
Safety guard for cutting (Art. No.: 44.500.09)
9. Disposal and recycling
The equipment is supplied in packaging to pre-
vent it from being damaged in transit. The raw
materials in this packaging can be reused or
recycled. The equipment and its accessories are
made of various types of material, such as metal
and plastic. Never place defective equipment in
your household refuse. The equipment should
Anl_TC_AG_125_SPK9.indb 18Anl_TC_AG_125_SPK9.indb 18 05.11.2019 08:25:0205.11.2019 08:25:02

EINHELL TC-AG 125 Specifications

General

Spindle thread	M14
Idle speed (max)	11000 RPM
Sound power level	94.2 dB
Sound pressure level	83.2 dB
Grinding disc diameter	125 mm
Vibration level (grinding)	4.9 m/s²
Vibration level uncertainty (grinding)	1.5 m/s²
Input power	850 W
Power source	AC
AC input voltage	230 V
AC input frequency	50 Hz
Sound pressure level uncertainty	3 dB
Product color	Black, Red

Weight and Dimensions

Width	115 mm
Height	100 mm
Length	295 mm
Weight	2100 g
Package weight	2300 g