Emerson EC3 Series User Manual

EC3-812_65118_EN_R00.doc Replacement for R00 3 / 5 PCN: 864916 18.03.2009
EC3-812 Dual Circuit Rack Controller
Operating Instructions
GB
List of Parameters
/ DISPLAY PARAMETERS
Min Max Unit Def. Custom
/1 Value to show 0 4 - 0
0 = compressors states (controller 1 and controller 2)
1 = suction pressure 1 (bar)
2 = saturation temperature from suction pressure 1 (°C)
3 = suction pressure 2 (bar)
4 = saturation temperature from suction pressure 2 (°C)
CONTROLLER C1 (LT)
P
SET-POINT PARAMETERS (C1)
P0
Suction setpoint -1 50.0 bar 3.0
P1 Suction band 0.0 50.0 bar 2.0
P3 Suction recovery min -9.9 50 bar -9.9
P4 Suction shift (0=disabled, 1=enabled) 0 1 - 0
P5 Suction shift max 0.0 3.0 bar 3.0
P8 Discharge recovery max -9.9 50.0 bar 50.0
P9 Discharge recovery step 0.0 5.0 bar 1.0
t TIME PARAMETERS (C1)
t0 Integration time 300 990 10 sec* 600
t1 Suction request on time 0 990 10 sec* 30
t2 Suction request off time 0 990 10 sec* 30
t3 Compressor min on time 0 990 10 sec* 180
t4 Compressor min off time 0 990 10 sec* 420
t5 Compressor cycle rate
(0=number of switching unrestricted)
0 199 1/hr 199
A ALARM-PARAMETERS (C1)
A0 Alarm delay LP 0 990 10 sec* 0
A1 Alam delay HP 0 990 10 sec* 0
A2 Suction warning min -1.0 50.0 bar 1.0
A3 Suction warning max -1.0 50.0 bar 6.0
A4 Warning delay suction min 0 990 10 sec* 0
A5 Warning delay suction max 0 990 10 sec* 0
A6 Maximum discharge end temperature 50 150 °C 120
A7 Discharge end temp. alarm delay 0 990 10 sec* 30
A8 Alarm delay serial alarm 0 990 10 sec* 0
A9 Compressor service interval 0 990
10 000
hr**
0
u STEP ENABLE PARAMETERS (C1)
u0 Comp service interval reset 0 5 - 0
0 = do nothing
1 = reset operating time compr. 1
2 = reset operating time compr. 2
3 = reset operating time compr. 3
5 = reset operating time all
compressors
u1 Compr.1 enable (0=disable, 1=enable) 0 1 flag 1
u2 Compr.2 enable (0=disable, 1=enable) 0 1 flag 1
u3 Compr.3 enable (0=disable, 1=enable) 0 1 flag 1
c
APPLICATION PARAMETERS (C1)
c1 Number of compressors 1 3 - 3
c3 Control mode 0 3 - 2
(0 = P mode, 1 = PI mode, 2 = dead band mode, 3 = binary mode)
c4 Compressor 1 control mode 0 2 - 0
0 = in standard control loop,
1 = act as base load compressor,
2 = act as modulating capacity;
0…10V for inverter command
c5 Compressor rotation 0 1 flag 0
0 = FILO logic (First In, Last Out) 1 = FIFO logic (First In, First Out)
c6 Sensor fail (number of compressors in
case of sensor failure)
0 3 - 0
h0 Discharge pressure
0 = not available; 1 = available
0 1 flag 1
r SENSOR PARAMETERS (C1)
r0 Suction sensor 1 0% -1.0 50.0 bar -0.8
r1 Suction sensor 1 100% -1.0 50.0 bar 7
r2 Suction sensor 1 offset -1.0 1.0 bar 0.0
r3 Refrigerant 0 7 - 3
0 = R 22
1 = R 134a
2 = R 507
3 = R 404A
4 = R 407C
5 = R 410A
6 = R 124
7 = R 744
* Unit on ECD-000 data entry. EMS allows data entry in sec.
** Unit on ECD-000 data entry. EMS allows data entry in 1000hr
*** Unit on ECD-000 data entry. EMS allows data entry in hr
F MODULATING PARAM. (C2)
Min Max Unit Def. Custom
F0 Compressor INV setpoint -1.0 50.0 bar 3.0
valid only for dead band control (c3 = 2),
not valid for P (c3 = 0) and PI control (c3 = 1);
with P/PI control the modulating set-point is the P0 parameter
F1 Compressor INV band 0.0 50.0 bar 2.0
valid only for dead band control (c3 = 2),
not valid for P (c3 = 0) and PI control (c3 = 1);
with P/PI control the modulating pressure band is the P1 parameter
F2 Compressor INV min speed 0.0 100.0 % 0.0
F3 Compressor INV max speed 0.0 100.0 % 100
CONTROLLER C2 (MT)
P
SET-POINT PARAMETERS (C2)
P0 Suction setpoint -1 50.0 bar 3.0
P1 Suction band 0.0 50.0 bar 2.0
P3 Suction recovery min -9.9 50 bar -9.9
P4 Suction shift (0=disabled, 1=enabled) 0 1 - 0
P5 Suction shift max 0.0 3.0 bar 3.0
P8 Discharge recovery max -9.9 50.0 bar 50.0
P9 Discharge recovery step 0.0 5.0 bar 1.0
t TIME PARAMETERS (C2)
t0 Integration time 300 990 10 sec* 600
t1 Suction request on time 0 990 10 sec* 30
t2 Suction request off time 0 990 10 sec* 30
t3 Compressor min on time 0 990 10 sec* 180
t4 Compressor min off time 0 990 10 sec* 420
t5 Compressor cycle rate 0 199 1/hr 199
A ALARM-PARAMETERS (C2)
A0 Alarm delay LP 0 990 10 sec* 0
A1 Alarm delay HP 0 990 10 sec* 0
A2 Suction warning min -1.0 50.0 bar 1.0
A3 Suction warning max -1.0 50.0 bar 6.0
A4 Warning delay suction min 0 990 10 sec* 0
A5 Warning delay suction max 0 990 10 sec* 0
A8 Alarm delay serial alarm 0 990 10 sec* 0
A9 Compressor service interval 0 990
10 000 hr**
0
u STEP ENABLE PARAMETERS (C2)
u0 Comp service interval reset 0 5 - 0
u1 Compr.1 enable (0=disable, 1=enable) 0 1 flag 1
u2 Compr.2 enable (0=disable, 1=enable) 0 1 flag 1
u3 Compr.3 enable (0=disable, 1=enable) 0 1 flag 1
u4 Compr.4 enable (0=disable, 1=enable) 0 1 flag 1
c
APPLICATION PARAMETERS (C2)
c1 Number of compressors 1 4 - 4
c3 Control mode 0 3 - 2
c4 Compressor 1 control mode 0 2 - 0
c5 Compressor rotation 0 1 flag 0
c6 Sensor fail 0 3 - 0
h0 Discharge pressure 0 1 flag 1
r SENSOR PARAMETERS (C2)
r0 Suction sensor 1 0% -1.0 50.0 bar -0.8
r1 Suction sensor 1 100% -1.0 50.0 bar 7
r2 Suction sensor 1 offset -1.0 1.0 bar 0.0
r3 Refrigerant 0 5 - 4
F MODULATING PARAMETERS (C2)
F0 Compressor INV setpoint -1.0 50.0 bar 3.0
F1 Compressor INV band 0.0 50.0 bar 2.0
F2 Compressor INV min speed 0.0 100.0 % 0.0
F3 Compressor INV max speed 0.0 100.0 % 100
H OTHER PARAMETERS
H2 ECD Display access 0 3 - 3
0 = all disabled (Caution, access to
controller only via TCP/IP network
possible)
1= Keyboard enabled
2= IR remote control enabled
3= Keyboard and IR control enabled
H3 IR access code 0 199 - 0
H5 Password 0 199 - 12
Note: Concerning the indicated parameters, it is recommended to check, before
installing, if the factory value is suitable for the required use

Emerson EC3 Series Specifications

General

Brand	Emerson
Model	EC3 Series
Category	Controller
Language	English