-----ASSEMBLY-----
INSTALLING LOADER FRONT
MOUNTING
BRACKET
AND
FRAME
SUPPORT
BRACKET
1300
Tractor
1.
Attach
front
mounting bracket (7), Figure
1,
to
each side
of
the tractor frame
with
four
cap
screws
(8)
and lock nuts (6).
2.
Attach frame support bracket (3), Figure
1,
to
the mounting pads
(9)
on each side
of
the tractor
transmission case. Use six metric cap screws
(4)
and lock washers (5).
3.
Attach each loader side frame
(10)
to
the frame
support bracket and
front
mounting bracket
with
four
cap screws
(2)
and lock nuts ( 1). See Figure
1.
NOTE: Tighten attaching bolts only enough to
hold side frames
in
position on the tractor
at
this
time; after installing the boom, tighten
all
moun-
ting bolts, alternating between right and left
mounting brackets.
1500 and
1700
Tractors
1.
Attach front mounting bracket (8), Figure 2,
to
each side
of
the tractor frame
with
four cap
screws (9), flat washers
(7)
and lock nuts (6).
2.
Attach frame support bracket (3), Figure 2,
to
the mounting pads (
10)
on each side
of
the trac-
tor
transmission case. Use six metric cap screws
(4)
and lock washer (5).
3.
Attach each loader side frame
(11)
to
the frame
support bracket and
front
mounting bracket
with
four cap screws
(2)
and lock nuts ( 1). See Figure
2.
10
NOTE: Tighten attaching bolts only enough to
hold side frames
in
position on the tractor
at
this
time. After installing boom, tighten
all
mounting
bolts, alternating between right and left moun-
ting brackets.
INSTALLING
BUMPER
1300, 1500 and 1700 Tractors
1.
Attach bumper spacer ( 18), Figure 3,
to
the right
side frame (
12)
with
1
/2"
x
4-1
/2"
pins (
11)
and
hair cotter pins ( 19).
2.
Place the square shank
of
a 7 /
16
x
3-1
/2"
bolt
(17)
through the square hole in the bumper
spacer and through the slot in the left side frame
(13). Secure the bolt
with
handle
nut
(15). Insert·
cotter pin
(16)
through the end
of
the bolt.
NOTE:
The curved bumper spacer (not shown)
must
be
completely removed from the side
frames to tilt the tractor
hood
forward.
INSTALLING
BOOM
LIFT
FRAME
1300,
1500
and
1700
Tractors
1.
Screw grease fittings (
10)
into the ends
of
the
boom arms.
2.
Attach boom frame
(21)
to
side frames
(12)
and
(13)
with
1 x
3-3/8"
pins (3),
3/8
x
1"
ser-rated
screws (2), and lock nuts (1).
INSTALLING CYLINDERS
1.
Attach rod ends
of
lift
cylinders
(20)
to
side
frames with
1"
x 2-7
/8"
pins (6). Place
machinery bushing
(8)
on pins and secure with
1 /
4"
x
1-1
/2"
cotter pins (7),
as
shown in Figure
3.
2. Attach base
of
lift
cylinders
to
boom
with
1"
x
2-7
/8"
pins (6). Place machinery bushing
(8)
on
pins and secure
with
1 /
4"
x 1-1/
4"
cotter pins
(7)
as
shown.
3. Attach base end
of
bucket cylinders
to
boom
with
1"
x 2-7
/8"
pin
(6)
and 1 /
4"
x
1-1
/2"
cotter
pin (7).
Be
sure
to
crimp the legs
of
the cotter
pins.
To Next Page
Loading...
Need help?
General